Scalarworks LDM Micro

In continuing the effort to keep my AR-15 cleaner, meaner and leaner, I've picked up a new mount for my red dot optic. I primarily run the Vortex Sparc II, paired with the occasional 3x magnifier. Vortex pairs the Sparc II with their own mount, which comes with a flat mount, a riser mount, and a spacer convert an absolute co-witness to a lower 1/3 co-witness.

I had grown discontent with the riser mount that comes with the Sparc II from Vortex as it is a solid chunky piece that weighs 2.435oz (3.095oz with the lower 1/3 riser) and uses a single hex screw as the cross bolt for picatinny or weaver rails. After a few years of swapping and remounting I've found the risers torx screw head to start stripping and retightening is more difficult. Instead of calling Vortex for a free replacement I decided to try something lighter with a better tightening mechanism overall.

The Scalarworks Low Drag Mount is a great alternative mount for the price point. Some may scoff at buying a mount thats only $50 than the Sparc II w/ mount included, but I felt the benefits would be worth while in the long run. The thumb knob was the selling factor for me, as I've never encountered anything that finger tightened so effortlessly with a rock solid clamping mechanism.

As indecisive as I am, I like to swap optics on pretty much every picatinny rail I own. Swapping between rifles, shotguns, and even pistols, the original Vortex Sparc II riser was bulky and required a tool for removal. It did provide elevation options to the user, but based on its omission from the latest gen optic the Sparc AR, its safe to say its not the slickest solution for AR-15s and Vortex has moved forward in their design department. The fact I can now move my optic forward or back on the rail, or swapping on a different firearm entirely greatly pleases me.

I sometimes choose to run a 3x magnifier behind the Sparc II, and ease of remounting to accomodate the magnifier when flipped to the side is a huge plus. If I opt to remove the magnification and position in the sweet spot just forward of the rear backup iron sight, the adjustment is quick and tool-less. Above all, the clamp the LDM uses is very strong and so far has produced repeatable zeros for my rifles, tho specific group sizes have yet to be scientifically recorded on my end.

I prefer absolute co-witness so I can align the circles of my rear aperature, optic tube and crescented front sight hood, but sadly I will have to make do with this until I upgrade my optic to an Aimpoint.

All in all, the Scalarworks LDM is a no brainer for someone looking to upgrade their factory optic and achieve a lighter firearm. The only real negative I can point out is the co-witness height is a bit screwy when using the Sparc II. Despite having the LDM100 absolute model, my iron sights sit at the lower third position on at 15" rail. This confused me at first, causing me to return the LDM to Rainier Arms and try the lower third LDM110 model which was way too high. EDIT: Scalarworks let me know that moving forward, the LDM/Micro Absolute Model will be lowered a tad to properly cowitness with the Aimpoint T2 (and Sparc II). I'm still happy with the LDM and will continue to use it in conjunction with irons, eventhough I wish it was a perfect absolute co-witness.

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: The Low Drag Mount’s precision guided telescoping clamp holds zero on every re-installation, and under the heaviest recoil. Guaranteed.

Target Market:  Aimpoint/Vortex Sparc owners

FNBs (Features & Benefits of this product):

  • Repeatable zero with each installation via precision telescoping clamp & thumb knob
  • Lightest Quick-Detach Aimpoint Micro mount in existence
  • CNC Machined from ultra high strength 7075-T6 Aluminum
  • Intuitive attachment system that won’t back out under sharp recoil
  • Adaptable to out of spec rails without additional adjustments
  • Streamlined profile free of protruding levers or knobs.
  • MATERIALS: 7075-T6 Aluminum Alloy / 4140H Steel Alloy
  • FINISHES: Mil-A-8625 Type III Hard Coat Anodizing / Black Nitride™
  • WEIGHT: 1.29oz LDM100 / 1.33oz LDM110
  • WARRANTY: Lifetime
  • HEIGHT OVER RAIL (OPTIC CENTER): 36mm (1.42″) LDM100 / 40mm (1.57″) LDM110
  •  COMPATIBLE OPTICS: Aimpoint Micro T-1, Aimpoint Micro T-2, Aimpoint Micro H-1, Aimpoint Micro H-2, Primary Arms Micro Dot, Vortex Sparc II

What other aesthetic options or finishes are available?: Absolute or Lower Third co-witness*

What others are saying?:

"The fit and finish on the LDM/Micro mount was also very nice. No sharp points or inconsistent anodizing at all. Just a very clean, high quality look. Another thing I noticed was that the anodizing seemed to match up color wise to my Aimpoint T-1 which at a quick glance makes it look like a one-piece Optic/Mount setup. The design itself I think is very attractive. So my initial impressions are very good. I am looking forward to using the LDM/Micro mount full time on my SBR this year. Pricing on the SCALARWORKS LDM/Micro mount is a bit higher than some of the other mounts on the market but I think the quality and lightweight/low drag aspect of it makes up for that very fast. One thing to note is that the LDM/Micro mount does not come with screws and requires that you use your “factory” screws. If you are like me and bought a T-1 with something other than the factory low mount you will probably need different screws. My T-1 came with the Factory LRP QD mount which has really long screws. Thankfully I had some screws from a different mount that I was able to use. This is not a problem, just something to keep in mind, when purchasing you might want to contact Aimpoint to purchase a new set of screws." www.AR15news.com

"I should point out that Scalarworks didn’t skimp on the clamping surface. The rail clamp runs the entire length of the side of the mount. Once the thumb wheel is turned to hand tight, the mount isn’t moving. I have the LDM110 which is the lower third co-witness model. I use it on a carbine that I purposely built to be extremely lightweight. At 1.37 ounces, it weighs less than half of the mount that it replaced on this build! To save that much weight on such a small part is amazing. The LDM seems to be extremely well made. The machine work is clean and the finish is even. The fit and finish on my example is excellent.  The LDM is the lightest Aimpoint Micro QD mount on the market by a wide margin. Heck, it is lighter than most non-QD mounts. It is well made, it mounts easily, it returns to zero at least as well as is required for the precision level of the optic it mounts, and it looks pretty darn good too. This is an impressive mount and I can’t wait to see how they adapt this design to support other optics. " Jerking the Trigger Review

PRICE POINT:

I need it now! Availability: Rainier Arms or Brownells

OUR RATING:

Pros:

  • Lightweight
  • Thumb Knob is knurled for grip, and employs a detent to prevent backing out
  • Clamping rail is full length
  • Compatible with multiple red dots
  • Clamping action will accomodate out-of-spec rail widths

Cons:

  • Co-witnessing a Vortex Sparc II with iron sights isn't consistent with other mounts with co-witness claims: 1mm higher than other compatible optics on AR-15s, 3mm higher on a Tavor -EDIT: Moving forward this will not be an issue as the Aimpoint T2 wasn't out yet when they made the Absolute LDM Micro. The new mounts will sit lower and achieve the proper absolute co-witness.
  • Included screws are button head and do not bite firmly with my used Sparc II, the original screws from Vortex are tapered head and are much more secure (may just be the internal threads on my optic are worn and the Scalarworks screws are a tad short with the head type.

SCORE: 8.5 GREAT

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

Hexmag Advanced Tactical Grip

  The Hexmag grip comes from the same company that brought us Hexmags. All of the Hexmag products I have seen come with a hexagonal pattern in them, thus the name. The pattern also adds a degree of flare to the looks of their products. 

  With the Advanced Tactical grip, you get this hexagonal pattern on the sides of the grip. And some raised straight lines on the front and back. But the big advantage to the Hexmag grip is its adjustability. One can choose 3 different positions or angles in which the grip sits. These are 17, 25, and 33 degrees. The setting are set up to help with different uses. The 17 degree is stated to help with AR pistols or close duty work. While the 25 degree is your standard AR grip angle. Leaving the 33 degree for a more relaxed shooting position, giving it more of a standard rifle stock feel. I found that the 25 degree position worked best for me. I guess that is why it was designed that way. 

  Now onto installation and adjustment.  The installation is very much like any AR pistol grip. Except that the Advanced Tactical grip has 2 parts. The first part holds the safety selector detent spring. It slides on as normal. Now you are left with the grip and the mounting screw. Both the grip and the mounting piece have large gear style teeth on them. Just put the screw through the handle and start tightening it as normal. Before it gets tight, position it on one of the 3 angles.  There are 3 locator lines on the back of the grip by the beavertail. These select which angle, just line them up and tighten the screw.  

  After using the grip for a while, I found it to be extremely smooth. Meaning that it was hard to get a good grip, and this was with dry hands. Hexmag sells grip tape that is cut to fit into the hexes, I would highly recommend this. I took it one step farther and stippled inside some of the hexes and also the front and rear of the grip. Besides being slick, having the option of adjustability is pretty nice. After I installed the grip, I was curious how the mounting system would hold up. Well it held up to me beating on a 2x4 with it. It didn't slip to one of the other positions, which I thought could happen. 

  If you are in the market for a new grip to enhance your AR rifle, look into the Advanced Tactical grip by Hexmag. But if you do decide to get one, get their grip tape or have it stippled. I liked the adjustability,  and now that it has been stippled, it is a nice grip

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Adjustable AR grip with cool hex pattern 

Target Market:

AR users looking for an aftermarket grip

FNBs (Features & Benefits of this product):

  • Hex pattern
  • Adjustable angles
  • Beavertail
  • Sturdy  

What other aesthetic options or finishes are available?

Black or FDE

What others are saying?:

Nice Grip 

Monte at Wise Tactical 5/5 stars

This Pistol Grip fit on my AR with no problem. It has a great feel to it and I really like that you can adjust the angle of it. It looks awesome on the Rifle, especially with the Hexmags.

Link to other reviews:

The Firearm Blog

Shooting Illustrated 

Price point:

MSRP = $27.99

Retail = $23.99 on Amazon

I need it now! Availability:

Amazon or check your local retailer

Our Rating:

Pros: 

  • Adjustable grip angle
  • Sturdy mounting system
  • Beavertail
  • Price

Cons:

  • Poor grip (slick)  
  • Has no storage inside grip

Score: 7.0 Good

 

Chad's favorite link: Saddle Butte Machine Gun shoot May 21 & 22, 2016

Fortis Rev II Handguard

Lighter handguards are becoming the new trend in AR-15 building.

Lighter handguards are becoming the new trend in AR-15 building.

AR15 handguards are about as ubiquitous as the rifle itself. Seems like more and more companies are springing up with a handguard for the dubious black rifle, and the tread seems to be lighter and more modular. With the proliferation of Keymod and MLOK rail attachment systems and less demand for full quad rail picatinny forends, the options for the end user have never been more plentiful.

The REV II's evolution brings more MLOK (or KeyMod) real estate while keeping the ounces down to a minimum.

The REV II's evolution brings more MLOK (or KeyMod) real estate while keeping the ounces down to a minimum.

I myself was interested in giving a lighter version a try, and I happened upon the Fortis REV handguards. Fortis machines some fantastic parts, and their handguards are now available in a Gen 2.0. The difference between the REV I and the REV II is the short forward rail sections in the 3, 6 & 9 o’clock positions that are present on the REV I have been removed on the REV II... and instead have been replaced with additional KeyMod/MLOK real estate and limited rotation QD sling swivel sockets.

The REV II uses the standard AR-15 barrel nut.

The REV II uses the standard AR-15 barrel nut.

The mounting collar uses four screws. 

The mounting collar uses four screws. 

I went with the 14" MLOK version of the REV II, and it is quite light. With a weight of only 9.3 ounces, Fortis really shed the excess with all of the milling and machining any of the 6061-T6 aluminum that wasn't crucial to structural integrity. The REV II uses a two part design where the main body is one solid piece, with a smaller mounting collar at the bottom rear. The REV II indexes by the two ear tabs that align on either side of the upper receiver, and a dovetail slot in the bottom that mates with the mounting collar and fastens with four screws and a 9/64 allen key.

The REV II still has the rear QD sockets for 2 point sling usage

The REV II still has the rear QD sockets for 2 point sling usage

Another design choice made to cut the fat was making the insider diameter much smaller than most other handguards on the market. At 1.340" the inside can still facilitate most low-profile gas blocks and the narrowest of suppressors like the AAC ECO-9/EVO-9 and most 22 cal cans. Be warned though, the screws/locking nuts of MLOK accessories will decrease that diameter by protruding inwards... making adding MLOK components and overlapping a can very problematic.

The narrow inside diameter of 1.34" will rule out some suppressors if you're planning on overlap, luckily the ECO/EVO 9 by AAC is 1.25" wide.

The narrow inside diameter of 1.34" will rule out some suppressors if you're planning on overlap, luckily the ECO/EVO 9 by AAC is 1.25" wide.


Overall with it's continuous top rail, anti-rotation index tabs, QD swivel sockets and use of the inexpensive and standard barrel nut, the Fortis REV II is a very nice handguard for the modern AR-15 build. The lighter weight will help keep your rifle lean and mean without sacrificing modularity

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: Fortis REV™ II is an extremely lightweight yet robust free floating rail system.  When designing the REV™, we didn’t want just another rail system, we wanted a better, lighter, feature rich handguard that was robust and within budget.

Target Market:  AR15 owners

FNBs (Features & Benefits of this product):

  • Material: Aircraft Grade 6061-T6 Aluminum
  • Finish: Military Specification Type III Hard Coat Anodized
  • Length: 7", 9", 12", & 14"
  • Weight (length and rail system dependant) 12" Keymod = 7.8 Ounces
  • Inside Diameter: 1.340"
  • Continuous Top Rail
  • Rotation Limited QD Sockets
  • KEYMOD at the 3, 6, & 9 o’clock
  • Anti-Rotation Tabs
  • Uses Standard AR15 Barrel Nut (Not Included)
  • Made in the USA

What other aesthetic options or finishes are available?:  Keymod or MLOK. Some dealers offer FDE Cerakote.

What others are saying?: "I purchased a 12″ Fortis REV Free Float Rail for use on my lightweight project build and it has served me well. I needed an extremely lightweight, extended rail that mounted on the standard barrel nut for a 14.5″ barrel with permanently attached muzzle device and the REV fit hte bill perfectly. Fortis has now released the REV II that is basically the same rail except the short the 3, 6 & 9 o’clock forward rails that are present on the REV have been removed on the REV II. They have been replaced with additional KeyMod real estate and QD sling swivel sockets. The result is a rail that weighs even less at just 7.8 ounces (the REV 12 weighs in at 9.2 ounces).

This looks like an excellent revision to the REV series of rails. I really don’t use the forward rails and actually find them to be a bit uncomfortable for how I hold the carbine due to some sharp edges. The new version removes the rails, saves weight, and costs less (at the introductory price). That is a win-win-win." Jerking the Trigger Review

"I thought the cardboard tube the rail came in may have been empty b/c it was so light.  I opened up the tube...it was in there.  The rail just looks amazing imo.  I had actually called Fortis to ask about the total overall length.  I have a 12.5 barrel+was wondering how much of the barrel would be left with no rail covering it .  I had read the OAL was a bit more than 9"(it's about 9.2").  The amount of barrel left exposed on my 12.5" BCM barrel(not counting the threads on the end of the barrel) is 2.75".  I think it was the head of Fortis that answered the phone(not sure if it was).  Anyhow, I was really impressed with Fortis's customer service b/c he answered all my questions.  The rail went on SUPER EASY!!!  Being that it was my 1st upper build, that made my day.  I can't say enough good things about the rail.  I'm a very happy customer.  Also, as far as Red Barn goes, it was fast shipping, a great price, and great packaging-Couldn't ask for more!" Red Barn Armory Review

PRICE POINT:

I need it now! Availability: Rainier Arms or Red Barn Armory

OUR RATING:

Pros:

  • Lightweight
  • Easy installation around standard barrel nut
  • Continuous top rail w/ no gap

Cons:

  • Indexing tabs still not close enough to upper receive to ensure zero/level. 
  • No 7 or 9 inch MLOK versions

SCORE: 8.0 GREAT

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

0 Likes

 

$170.95

GunVault SpeedVault SV500

Keeping a handgun in the home can be quite the catch 22, especially if you don't live alone. You want the gun easily accessible for the unexpected "bump in the night" scenarios, but leaving it carelessly in a nightstand or sock drawer can be pretty reckless. Especially if you have curious pups or nosey house guests that could find your weapon and potentially have a negligent experience. Keeping the firearm in a traditional handgun safe "keeps people honest" as so many like to put it, but often restricts the access due to size and weight of the safe, where you keep it, and how easy it is to open when the lights are out and wasted time could endanger your life.

I myself have lived in a few apartments over the years, and frequently have friends over to visit, often with children. I've grown accustomed to have some form of defense tool within arms reach of my bed, because frankly, bad things happen. Often it would be a compact sized pistol in a handgun-rated personal safe, which is more like a lockbox. The issue with this lockbox is it takes up alot of surface space, and is obvious as hell. Unless you bolt that thing down, consider it a fun puzzle begging to be solved by anyone who isn't you. Okay so what, you just slide it under the bed, lash it to the bed frame, or just bury it in your nightstand... well good luck getting to your protection now in the middle of the night, from a dead sleep in your pitch dark room, possible with your adrenaline pumping hard enough to hear your own nerve endings pop.

The facts are homes get burglarized/broken into by criminals, and criminals tend to work late shifts. AKA sleepy time for you. So when your alarm system's siren yanks your conscious mind out of la-la land, or the sound of your window shattering just after your head hits that pillow... thats when the timer starts counting down. This could be the difference between you being another victim of a B&E, or possible assault/homicide (check the news, pull your head out of the sand, it happens). You are particularly vulnerable at night, because your cognitive and motor functions suck when you are tired or after you have just woke up. I don't care who you are. In the scenario described above, fast and foolproof is how you want accessing your defensive firearm to be, but still be secure from unauthorized hands during the rest of the day. So you want fast security. Like a quick safe, or a rapid lockbox... or a SpeedVault!

There are plenty of personal safe manufacturers in the market, but few have the recognizability and popularity of GunVault. They are most notably known for their 'No Eyes' keypads and their biometric safes these days- which would seem like straight out of a spy movie just ten years ago. The SpeedVault is no exception with both biometric and traditional keypad configurations, but it's design is what makes it one of the most unique handgun safes available today.

While most personal safes contain handguns in a horizontal format with the pistol on its side, the SpeedVault supports the firearm vertically just like a holster on the belt. This unconventional vertical format, coupled with an adaptive mounting bracket, is perfect for two main reasons: you can mount it in low profile but easy to access locations, and when unlocked the gun's grip is exposed for a fast and unhindered grip. Just about the only thing it doesn't do is call 911 for you... but when seconds count and law enforcement is minutes away, you've at least got a gun in your hands!

The mounting bracket is ambidextrous, meaning you can mount it to either the left or right side of an object.

The mounting bracket is ambidextrous, meaning you can mount it to either the left or right side of an object.

First you line up the tabs with the safe's slots

First you line up the tabs with the safe's slots

Next thread the three thumbscrews into the bracket. The holes should be properly indexed when the hooks are in the mounting slots.

Next thread the three thumbscrews into the bracket. The holes should be properly indexed when the hooks are in the mounting slots.

Right out of the box, you could probably have the SV500 mounted, programed and fully operational in 20 minutes or less. That is, unless you have to run to the gas station because you don't have a spare 9 volt battery handy, and you glanced over the line on the package that said battery not included. While the included wood screws are kinda short, they allow you to mount the bracket right to the inside of a desk, headboard, nightstand, cupboard etc. without unnecessarily over-penetrating your furniture, or pinning your drawers shut accidentally. If you wish to mount into drywall or cinderblocks, I would suggest a trip to the hardware store because these screws are only good for wood.

The safe itself screws into the mounting bracket internally, which means I had to bust out the manual and read the instructions. You have to unlock the safe using either the key or the factory-programed code, remove the hinged door itself so you have enough room to insert screws from the inside and hand tighten against the mounting bracket. This may be a difficult task for large-mitted individuals so pliers may be needed. When the three screws are fastened, the safe itself conceals the screws holding the bracket to your surface of choice.

After a bathroom break and a victory beverage, the safe is ready for locking up your pistol, or reprogrammed to a code of your liking. Obviously with the biometric model SVB-500 you would scan in your fingerprints, as well as your spouse or any other authorized users. I chose the get the keypad version SV-500 because a.) it was cheaper and b.) I felt a manually entered sequence was less prone to fault than a biometric reader. OR rather, if a code didn't work, I would be to blame, not the SpeedVault. Entering my personal code is something I could train for and develop muscle memory.  Also if my fingers are ever injured or covered in blood, dirt, oil, Cheeto dust, etc. the keypad would still function.

The SpeedVault has a floorplate that secures the door to its hinge. You have to partially install the door inside the safe so the hooks go over the hinge bar, then you screw in the bottom plate to complete the installation.

The SpeedVault has a floorplate that secures the door to its hinge. You have to partially install the door inside the safe so the hooks go over the hinge bar, then you screw in the bottom plate to complete the installation.

What's really interesting is you have the option to program simultaneous button presses into your code sequence. So instead of 1,2,3,4,5,6 you could program 1,2-2,3,4-4-4,5,6 or any combination in between. Even though there are only four buttons, you are allowed a code between 3-6 keystrokes long. I like the idea of throwing a double press in the sequence because its not something a prying individual would typically try, and it increases the difficulty of it being figured out. Just be forewarned, the two/three combo finger presses have to be simultaneous, and the window for error is small.

If you miss or are slow with the other finger slightly, the entry will be incorrect.

Now keep in mind the safe will enter a "sleep mode" and lockout the keypad for 2 minutes if the correct code isn't entered within 24 key presses, and any additional attempts during that 2 minute period will makes the safe beep three times and the LED flash a red light. 2 minute "timeouts" between mischievous attempts should be long enough for a child to lose interest, and the tamper indicator feature allows you to see if someone attempted to open the safe since the last successful code was entered.

The SV-500 fits the entire full-size 1911 with no issue, and I can get my fingers around the frame to pull out.

One of the most popular complaints with digital keypads on a safe is the audible beep with each button press, and/or when successfully opened. The SpeedVault will beep like this from the factory, but it is very easy to disable the tones using the internal switch. Honestly it was the first thing I did when I got the SV-500 open, if I wanted it hear a beep every time I pushed a button I would just play with the microwave. An inward-facing internal bulb illuminates the gun when the safe is opened day or night, which I find useful and not intense enough to ruin my dilated pupils and kill my night vision. Its just enough to see where you are reaching if need be.

The inside is very simple, batter compartment, and two buttons: Learn (program) and Mute (no more beeps)

The inside is very simple, batter compartment, and two buttons: Learn (program) and Mute (no more beeps)

The biggest complaint about the SV-500 is the sound of the electronically powered mechanism inside winding up, followed by the "thunk" sound of the door becoming freed from the lock. Yes the hinged door does make another sound when gravity drops it to its fully opened position and contacts the stop, but this is not where the most audible of the sounds originate. Even when guiding the door open with your hand, the unlocking mechanism is the unwelcome noise. While I wouldn't call it entirely audible from the hallway outside the bedroom door (I've tested it) it is audible enough within the room. So if you plan to stash a candy bar in it for late night snack time, your partner will probably hear it and have some choice words.

Note: If you are a wheel-gunner through and through, barrels longer than 4 inches will bottom out and not fully support the firearm in the foam pocket. This causes the gun to droop and the grip to protrude from the door.

Internally, the 'holster' part of the safe is comprised of a foam pocket. This rectangular pocket is meant to hold your gun's slide, exposing the frame and grip for easy extraction. The depth of this pocket can facilitate a full-size 5" 1911, but anything larger I would have my doubts (a Desert Eagle would probably be incompatible). Obviously something in the compact range is ideal too, with room for an extra magazine if its small enough. The pocket isn't cut that large, but it is only foam so it nicely stretches and conforms around the slide and the light correctly.

I was surprised to find my S&W M&P357c fit even with a Streamlight TLR-3 light

All in all, the SpeedVault is fantastic. Not only can you mount it beside your bed or even under your desk at the office (where allowed) but the speed at which you can withdraw your handgun is exceptional. The only negatives I can think of are the noisy unlocking mechanism and the finicky double or triple code presses. I've also tried a larger gun and light combo for fit, the Glock 17 with Streamlight TLR-1 checks out. I keep my gun in condition 1 inside the SV-500, meaning a round chambered, full magazine in place and hammer cocked (or in my case, striker). Whether or not you leave the safety engaged is your preference, I'm used to carrying without a safety so my M&P is ready to go as soon as its in my hand.

FIREARMS INSIDER REVIEWS – 8 KEY POINTS

Claim to Fame: Keep your handgun safe, secure and ready for action with the SpeedVault. Offering a revolutionary design, the SpeedVault is equally as fast as it is discreet. It is the ideal choice for a home or business looking for added security

Target Market:  Those seeking basic gun security w/ quick access in the home or office

FNBs (Features & Benefits of this product):

  • Digital Keypad (biometric version also available)
  • Multiple mounting options
  • 18-gauge steel construction
  • Tamper resistant door
  • Backup override key included
  • Audio and LED low battery warning
  • Foam lined interior
  • Weight 6.61 lbs
  • Outer Dimensions 13"L x 3.5"W x 6.5"H

What other aesthetic options or finishes are available?: Black Only, but biometric access available in SVB-500 model.

What others are saying?: " 4/5 Stars - Works great, easy to install (I watched a video on YouTube) and I would recommend to anyone wanting immediate access to their weapon by their bedside, and also for safety reasons as children cannot gain access without the code or key. Also great to have the keys as backup in case our memory goes away (with age) and we forget the code. :-) Only concern is light does come on when it opens and there's a pretty audible "clunk" when the drawer drops." Sportsmans Warehouse User Review

" This is not a safe against determined intruders, nor is it a fire safe. It is a safe that will stop kids and honest adults from getting the gun while keeping it ready to use if needed. If you want a serious gun safe, then don't buy this and then complain that it is thin metal (but not flimsy by any measure). After installing it (with the short screws on solid wood) I can say that it would take a heck of a blow from a sledge hammer to knock it loose, or a determined assault from a crow bar, but again, it is not designed to stop a determined attack. Finally, if you are concerned about the people saying it is too loud, or the light is too bright, here's a reality check. As much as I like to imagine myself as Liam Neeson going rogue and blasting my daughter free from sex traffickers, this is not the case. This is not a product for black ops agents, it is a product for responsible gun owners with families. If we have to draw a gun against a person to defend ourselves in our homes, a light or a whirring is the least of our problems. It is a great product and the price is right." Amazon User Review

PRICE POINT:

I need it now! Availability: Brownells, Amazon or many sporting goods stores

OUR RATING:

Pros:

  • Very simple to program
  • Large buttons easy to use without vision
  • Keypad sequence can contain combinations of 2-3 buttons simultaneously pressed
  • Bright white internal light illuminates contents
  • Audible beep when buttons pressed is easily muted/turned off
  • Flexibility in mounting options (left or right side, desks, nightstands, etc.)
  • Easy programming + physical key backup
  • Steel construction feels extremely solid
  • Internal foam lined 'pocket' holds various gun models/sizes, even with light or laser accessories

Cons:

  • Very audible mechanical whining and "clunk" noise as the electronic latch locks/unlocks
  • Mounting bracket lacks screw hole options for wall stud
  • Included mounting screws are short
  • Double or triple press codes are finicky and can cause incorrect entries
  • Low battery warning only when keypad pressed

SCORE: 8.5 GREAT

 

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design

Axelson Tactical TALON muzzle brake

  The AxeTac TALON muzzle brake is made by Axelson Tactical out of Nevada. If you recognize the name it might be because the company was started by the brother of Matt "Axe" Axelson of Lone Survivor Fame.  They have brought out a number of products for AR-15 type rifles, along with their AXE series complete rifles.

  I have put quit a few rounds through the TALON brake they sent me. I also have shot a couple of the AXE rifles with them installed. The brake does an excellent job of reducing felt recoil, not that a 5.56 AR has much recoil. But what I was most impressed with was its ability to keep muzzle rise to almost nothing. It was easy to get accurate double taps, shooting off hand, at a 24" steel target at 200yds. This was with a 16" barrel and a red dot optic.

  The AxeTac TALON is sold as a muzzle brake, but it really is more. It is noticeably louder than a standard A2 flash hider, but not as loud as my 3 port comps that direct the blast out the sides. The TALON also does a great job as a flash hider, keeping the flash contained within it. And as a compensator it also does an excellent job. It will still allow some of the blast to go forward, but it doesn't seem to hurt its effectiveness as a comp. I ran the TALON on a 16" and an 11.5" AR. Yes, it worked better on the 16", but it worked quite well on the 11.5" also.

  Now onto the technical stuff. The TALON has 3 small slots, 1 facing up, and the other 2 facing the sides but slightly lower than 90 degrees. It also 2 large ports between the small slots. And 3 open ports at the end spaced evenly. The bottom is mainly closed except for the port at the end of the muzzle. Also on the bottom is the Axelson Tactical logo. The brake is 0.940" in diameter, and 2.5" long, not counting the crush washer (which is included). There are also flats to fit your standard muzzle device tools or a 3/4" wrench. It is made from stainless steel, heat treated, and then black Melonite coated. It is threaded the standard 1/2"-28.

  I would not hesitate to install one of these on another rifle. The finish is excellent. It does a good job at being a comp, brake, and flash hider. It's made in the USA. If you are looking for a good all around muzzle device, check into the Axelson Tactical TALON muzzle brake.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

AR-15 Muzzle Brake, Compensator, and Flash Hider all in one.

Target Market:

Shooters looking to mitigate recoil.

FNBs (Features & Benefits of this product):

  • Reduces felt recoil

  • Reduces muzzle rise

  • Reduces flash

  • Made from stainless steel

  • Melonite coated

What other aesthetic options or finishes are available?

None

Link to other reviews:

Google was not my friend and I could not locate any

Price point:

MSRP = $94.99

Retail = $94.99 on Amazon

I need it now! Availability:

Axleson Tactical or Amazon

Our Rating:

Pros:

  • Reduced recoil

  • Almost no muzzle rise

  • Melonite coated

  • Stainless Steel

  • Made in USA

  • Includes crush washer

Cons:

  • Price

  • Longer than a standard birdcage flash hider

85.jpg

Score: 8.5 Great

 

 


Chad's Favorite: Patriot Patch Co.

HCMAGS HC3R 10/22 magazine

   HCMAGS is a company that makes an easy loading magazine for the 10/22, or any other firearm that uses 10/22 magazines. I first saw one of their magazine systems at a local gun shop. The idea looked really cool, so I purchased one. The magazine holds 25rds of .22lr with a side saddle that holds another 20rds for quick loading. 

  The HC3R magazine can be used like any other mag, but why? Well, since the HC mag has a slider on the side of the magazine, you could just slide it down while loading it up. But there's more. The back of the magazine acts like a stripper clip. One can push it down slightly and rock the whole stripper clip out. Fill the clip up with 25rds, pull the slider on the side of the mag down and lock it in place. Then roll the clip back into the magazine and release the slider and your ready to go. When the clip is off of the magazine, you can also put 20rds in the magazine side saddle before loading up the other 25rds. Once you have depleted the contents, you can take the stripper off of the magazine, slide it over the rims of the 20rds in the side saddle, and reinstall it with 20 new rounds. An extra stripper clip is included also. 

  Now I would have thought that this was the best thing since sliced bread. The biggest problem is that I couldn't get the magazine to feed in 3 different 10/22's. HCMAGS instructions say to watch their video on their website to make sure you are loading the magazine correctly. I watched it 3 or 4 times and still the magazine wouldn't work. I called them and they told me that I had a 1st generation HC3R mag and when the 2nd gen was out they would replace mine with a gen 2. They replaced it after about 6 months. Okay, sometimes manufacturing takes longer,  so I was alright with that. Now I have my gen 2 in hand, and it works a little bit better. It only jams about every 3rd round, instead of every time. I can't load 25 in the mag or it won't even feed, I have to load 20 to get it to feed the first round. Different manufacturers of .22lr don't seem to make a difference either. As is with different 10/22's.

  Basically the HC3R magazine is an innovative design. It is kind of a shame that it doesn't live up to its hype. 

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Quick reloading 10/22 magazine

Target Market:

Someone who wants extra magazine capacity without the need for an extra magazine. 

FNBs (Features & Benefits of this product):

  • Quick reloading 
  • Stripper clips
  • Lockable thumb stud
  • Extra ammo on hand in magazine side saddle
  • Disassembles for cleaning

 

What other aesthetic options or finishes are available?

Tactical pack available with extra stripper clips, loader, and case. 

Tactical pack

What others are saying?: 

 Bill K. at Botach 2/5 stars

Cumbersom

This magazine is difficult to load for me. I found bullets jamming during the loading process and falling out of the Rib Clip and extra holding channel when I didn't hold it properly. For me, it is more hassle than it's worth.

LEXRated at Cabelas 5/5 stars

Awesome and Innovative

There's not much real fun in loading, but this system these folks have developed is simply amazing.

Follow their instructions and get a couple extra magazines and this system will let you shoot all day and even for days. It is effortless.

NOTE: this listing is incorrectly listing the magazine as a 20 round magazine. Once they update the product to show it is in fact a 25 round magazine and it's part of the whole system whereby the strip clip feeders hold 20 rounds on the same mag. That means with one mag you have 45 rounds, 25 in and 20 out, and dumping the 20 in is super fast.

I hope Cabela's gets the HC Mags HC3R Tactical Kit (I have one already) but others need to know about it. I do not work for HC, just an impressed customer of their product and fan of Cabela's.

Additional note: some may say that having an open/exposed magazine makes it not worth it, but considering how much more one typically shoots with 22, i see the value in making the loading delays and effort go away and getting back to shooting more important. Plus, it's a breeze to clean and frankly, most of any significant debris easily going in, can fall out the same way. Mud is mud and play safe.

Price point:

MSRP = $29.95 at HCMAGS

Retail = $30.00 at Botach

I need it now! Availability:

HCMAGS.com

Our Rating: 

Pros:

  • Stripper clip
  • Steel feed lips
  • Ease of loading
  • Comes apart for cleaning  

Cons:

  • Will not feed properly
  • Shouldn't need special loading instructions

 Score: 4.00 Bad

 

 

 

Chads favorite link of the day: Northwest Firearms

VLTOR SM-O QD Offset Scout Mount

This VLTOR flashlight QD mount goes by SM-O: Scout Mount Offset

Here at the Firearms Insider, we've reviewed a lot of rifle accessories. I've seen my fair share of flashlight mounts, in polymers and pot metals alike. Like flashlights themselves, the options for mounting solutions that exist in the firearms market come in all shapes and sizes.... with lots of terrible, cheap and faulty options on the market. Lucky for you, I was in the market for a quality "cry once, buy once" light mount about a year ago, and have only positive results to report back. 

In picking up quite a few "modern sporting rifles" as well as pistols and a scattergun or two, I was in the market for a quality mount that had a quick detach function so my light could jump from weapon to weapon as I see fit. What I landed on was the VLTOR SM-O: Scout Mount Offset QD. The VLTOR SM-O comes in a QD cam lever version, which is made by American Defense. If you are looking for rock QD solid mount that will hold up on all weapon platforms - from rifles and carbines to even the jarring recoil of the shotgun, ADM makes some fantastic mounts. In my experience with buying cheap mounts and then later replacing them with better quality versions, almost everything made by American Defense straight up rocks! Seeing this mount was a combined effort between VLTOR and ADM was almost reason enough to give it a shot.

The SM-O is unique in that it's clamping mechanism simultaneously grips the picatinny rail AND tightens the one piece ring around the light. When adjusted correctly to your light's body diameter, it secures the light when the cam locks down, but easily releases the light when the cam is unlocked, allowing for easy adjustment for your ergonomics.

The headline act of VLTOR SM-O is its QD mount. Easy to remove, easy to reverse for your rifle.

Adjusting the SM-O for your specific light does require some light tinkering. This is the only time a tool is ever really needed. Basically you need to adjust a bolthead when the light is removed, then try inserting the flashlight into the ring body, and throw the QD lever to check for difficulty and resistance. Too hard to throw completely 180 degrees and you'll need to unlock the cam and remove the flashlight to loosen the fit. Too loose and your light can spin in the ring body and the cam won't snug that rail like it should. Its a bit of a back and forth dance to find the proper balance of secure fit, but once you find it, its clear sailing.

I've been primarily mounting a pair of SureFire G2X Pro lights on just about every railed part I own over the last year, from AR-15 handguards, AK-47 forends, Tavor MLOK rails, shotgun barrel clamps, and even tactical scope rings. The SM-O worked on everything, and the tension never loosened from my initial configuration no matter how many times I played musical picatinny rail with this thing. Removal and replacement can be done in seconds, and with just one single hand. If the offset is putting the light too high or low for your liking, just invert it and reverse the flashlight. No one will call you out on the VLTOR logo being upside down.

Got tactical scope rings? The SM-O makes for a great optic mounted light for nighttime shooting without interfering with scope turrets. 

Even if you don't have a tactical plinker decked out in all the bells and whistles, this simple mount is quite handy for the varmint hunter as well. Mounted on a railed scope ring cap or tactical accessory scope ring, this mount provides a perfect offset light that will hold up to whatever you can throw at it. And if you find yourself needing and handheld light for not shooting purposes, you've got one in seconds.

All in all, this product leaves me conflicted. I wish I could afford more of these for each one of my modern sporting rifles. Then again, I don't need to because of how easy it can jump from gun to gun. So until this one blows up or grows legs and runs away, the SM-O will always have a home in my arsenal.

Firearms Insider Reviews – 8 Key Points

Claim to Fame: The Offset Scout Mount is manufactured in conjunction with American Defense Manufacturing, and is a fully ambidextrous, offset light mount available with either conventional thumb screw mounting or throw-lever quick disconnect.

Target Market:  Civilians and Professionals with railed rifles or carbines

FNBs (Features & Benefits of this product):

  • Either thumb screws or throw lever mounting
  • Made from 6061 T6 aluminum
  • Hard coat anodized
  • Adjustable tension
  • Minimal / Low Profile 

What other aesthetic options or finishes are available?: Black Only

What others are saying?: "I've tried a lot of light mounts over the years. This is by far the best. The unique mechanism of the American Defense cam lever is easier on rails that the LaRue mount, making this mount better in my opinion, and less expensive. The cam makes for a secure mount that will not loosen like thumb screws, and because of the large bearing surface does not require much pressure to hold it securely in place. I also like that the caming action also holds the light in place. This enables the light to be quickly and easily removed from the mount, turned around or reconfigured. This enables it to work with every rifle I've tried it on. I've now got a box full of used light mounts for sale." Brownells User Review

"I love this QD flashlight mount. I've bought several flashlight mounts for my rifles and shotguns. I have had the cheaper plastic mounts that just can't hold the flashlight securely with the recoil of a shotgun. This mount is also much easier to use than others due to the QD feature. The off-set angle mounts the flashlight at an angle I prefer, keeping it out of the way of a DBAL or other accessories you may also want to mount. I plan on replacing several of the mounts with this model.

." Amazon User Review

PRICE POINT:

I need it now! Availability: Brownells, Amazon or many online stores

OUR RATING:

Pros:

  • Very durable finish
  • Mount can be removed easily for attaching to another position or weapon
  • Light itself easily removable when cam in unlocked for maintenance or reconfiguration
  • Minimal footprint on the rail

Cons:

  • Minimal instruction for adjusting tension

SCORE: 8.5 GREAT

 


Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
Hunter of Design


SureFire G2X Pro LED Flashlight

The new tactical duo that've been illuminating my life, the SureFire G2X LED Dual Output.

As flashlight technology improves, we start to see entry level lights become more and more advanced with features that used to be reserved for higher end models. Features like LED and dual outputs are great to have for other purposes than high speed low drag operator types. Combine those with a durable body and a pocketable size, and you've got yourself a quality light for everyday carry, that won't kill your wallet.

The G2X Pro runs on two 123A batteries

Enter the SureFire G2X Pro. Its simple light, built to survive harsh use and give the user dual output in a simple tail cap button. Nothing to twist to turn, just an easy to use button that can switch between a low, long runtime settings and a very bright shorter runtime option. The first press of the button delivers 15 lumens at its low setting. With a runtime of 4.5 hours, 15 lumens does seem like a hallway nightlight. Compared to any other light it seems underpowered, but the 15 lumens is great for smaller tasks at night without ruining your pupil's night vision from excessive light splash. Searching the backseat of your vehicle, or checking inside a dufflebag when the power goes out, or not blinding your significant other inside the tent on your camping trip.

The higher output mode of 320 lumens is vastly brighter with a farther reach. Originally Surefire had the higher end capped at 200 lumens, but they have since added another 120 lumens so make a staggeringly blinding light from the LED emitter. This setting is great for outdoor and indoors, especially in a searching or defensive role. This level of lumens is enough to temporarily blind an assailant, so it works great as part of your EDC gear with your defensive pistol or mounted onto your rifle/carbine/shotgun. It's 1 inch body and 1.25 inch bezel make is well suited for a long gun or carbine using any number of mounts. Even for the unarmed dog walker, the higher setting is useful for illuminating objects or hazards at a distance.

Shown on the left is the 15 lumen low setting, and the 320 lumen high setting on the right.

The tail cap button also has two levels of activation, a partial depth that serves as a momentary on position, and a full press that clicks and locks. Its a bit tricky at first to get the hang of the optional press depth as well as the dual output setting, but once you get the hang it, I find it advantageous. Sometimes you only need a brief moment of light, to find your keys on the ground or to clear areas of threats without indadvertedly broadcasting your position with too long of an activation. The partial depth also speeds the time it takes to "double tap" to the higher 320 lumen setting right off the bat. At that point you can either fully depress to lock it in at 320 lumens, or simple maintain the partial pressure until the light is no longer needed and you just release. As far as the flood itself, the reflector is micro-textured and delivers pretty wide beam with generous peripheral spread.

The G2X Pro pairs well with rail-compatible weapon mounts. The FDE matches the Viking Tactics FDE mount perfectly.

If you don't like the dual output function, which is fully understandable, the G2X Tactical model is available at 320 lumens full time all the time for the same price point. I can report that the G2X Pro's time to double click the button can be as slow as two mississippis between presses to still get that 320 lumens mode. Of course double pressing faster than that will still work that higher mode.

The business end of this light is very sturdy.

The biggest selling point to this compact flashlight is its sheer durability. The polymer body is constructed of Nitrolon® and is smoothly sculpted for a comfortable grip and resists scratches, abrasion, and corrosion... not to mention gives a good grip. The high-efficiency LED make the light virtually immune to failure to damage... and since there's no filament to burn out or break, the light will easily outlast more conventional bulbs.

Overall I really like this SureFire. Admittedly the under $100 price point is what got me to give it a try, but after testing two models as an EDC light and a dedicated rifle mounted light, I am am very pleased with the G2X. Its a very solid, minimal light that I will try hard not to lose (hence why I bought two).

Firearms Insider Reviews – 8 Key Points

Claim to Fame: The G2X Pro is a compact yet powerful polymer-body flashlight that uses a high-efficiency LED to provide two light output levels: brilliant & penetrating.

Target Market:  Civilians and Professionals

FNBs (Features & Benefits of this product):

  • Virtually indestructible LED emitter regulated to maximize light output and runtime
  • High 320 lumen 2.5 hour runtime
  • Low 15 Lumen 4.5 hour runtime
  • Two output levels—high for maximum light, low for extended runtime
  • Precision micro-textured reflector creates smooth, optimized beam
  • Tough polycarbonate window resists impact
  • Tough Nitrolon® body, anodized aluminum bezel
  • 1" body, 1.25" bezel
  • Dual-output tailcap click switch—press for momentary-on low, click for constant-on low, return to off then press or click again for high
  • Weatherproof—O-ring and gasket sealed
  • Includes high-energy 123A batteries with 10-year shelf life

What other aesthetic options or finishes are available?: Black, Desert Tan, Forest Green, Yellow

What others are saying?: "I have older G2's prior to the recessed click tail cap. The ability to activate the light for momentary or constant without having to turn the rear cap is very handy. I also appreciate the 320 lumens over the older 200.  This is a very robust, bright light, with an excellent beam at a great price." User Review

"I've owned a number of the SureFire flash lights. Best darn flash light ever made. The problem I seem to have is every so often it grows legs and runs away. Even though I purchase lanyards they still seem to get away from me. All kidding aside, I love their products and am a firm believer you get what you pay for. I use them day in and day out. So much I wore out and requested a replacement switch fully expecting to pay for it. To my surprise and delight I received one in the mail in a couple of days at "NO CHARGE". Now thats what I call a great company that stands behind their product. Hands down, the best." User Review

 

Price point:

I need it now! Availability: Brownells, Amazon or many online stores

Our Rating:

Pros:

  • Very Durable construction for tossing around or pocket carry
  • Can toggle tailcap button or momentary press
  • Works well with weapon-light mounts

Cons:

  • No provisions for pocket clips or lanyards
  • No Tape switch ability

Score: 7.5 Good


Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast
​Hunter of Design


Hipertouch 24C Trigger

The Hiperfire Hipertouch 24C for the AR15 is a multi-adjustable competition trigger system. It is a single stage trigger with a flat face and/or a trigger shoe. Hiperfire has been manufacturing AR triggers for a while now. The 24C is one of their flagship models. This trigger has been designed for competitions like 3-gun. It also would work well for varmint rifles.

The Hipertouch comes with 3 different pairs of springs. These springs adjust trigger pull weight and hammer fall energy. They come in blue, yellow, and plain. Blue springs are for medium trigger weights and stock hammer energy. Yellow are for light/medium weights and standard hammer energy. And then there are the plain springs. These are for a light trigger pull and Increased hammer energy, they also give the fastest lock time. This spring system is unique. When manually cycling the hammer you can feel it toggle over center. It basically pulls against the trigger spring to help reduce pull weights but still remain safe. I assume this also helps with lock time. I tried the different springs and ended up going with the plain ones for the lightest pull weight.

Along with the different springs, the 24C comes with a "Hipershoe". The hipershoe is a trigger shoe that can be positioned in any of the 5 different locations on the flat trigger. It is slightly curved and much wider than the trigger itself. The 24C does not require the hipershoe, and if not used, it is just a flat faced trigger (no curve whatsoever). Adjusting the hipershoe is pretty easy. It just slides up and down on the trgger and locks in place with a kind of detent system. With the shoe in its lowest detent, one will get the lightest trigger pull and the expense of a tiny bit of creep. With the shoe in the top detent, one gets an ever so slightly heavier pull weight, but with no noticeable creep. The pull weights vary between around 2lbs to 4.5lbs depending on what springs are selected and what position the hipershoe is in.

Installation on the 24C is not as easy as some drop-in style triggers. But it is not extremely hard either. Hiperfire sends some good instructions to help ease the installation pain. If you are not confident doing it yourself, just take it to a gunsmith and have it installed, they probably won't charge too much. First, of course, you must take the old trigger out. Then you take the trigger/disconnecter and install it like you would for a standard AR trigger. You can then slide the hipershoe on it (if you want it on). After that, intall the hammer just like normal. Now it gets a little more complicated, as you have to install the toggle shafts, pivot, spindle, and springs (mentioned above). I won't go into that, as the instructions do a great job. An extra hand might be advisable. After all of that, safety check it and go have fun.

This trigger is fantastic! It is super smooth, crisp, with a light pull weight. I have used it for 3-gun and target shooting. It has performed flawlessly with all types of ammo, including steel cased and .22LR with a conversion kit. When target shooting, the crisp pull and fast lock time makes for a great experience. If you are in the market for an aftermarket AR trigger, go look and see what Hiperfire has to offer. I don't think you will be disappointed.

 

Firearms Insider Reviews – 8 Key Points:

Claim to Fame:

Precision single stage adjustable trigger for the AR-15 platform Target Market: 3-gun, competition, varmint hunting, target shooting, and anyone looking for a really good trigger for an AR

FNBs (Features & Benefits of this product):

  • Adjustable
  • Hipershoe (wide curved trigger shoe)
  • Increased hammer energy
  • Increased lock time
  • Flat face trigger
  • Single stage

What other aesthetic options or finishes are available?

Essentially the same trigger but with a curved bow and no Hipershoe: 

HiperTouch 24 3G

What others are saying?:

By JustinInATX: 5/5 stars on Amazon

Best trigger I own. Just installed this on a high-end AR 308 build and it runs like a champ! It slams down with authority, twice as powerful as any other trigger I own. I've encountered a few light strike with my CNC 3.5lb trigger, but that's not even a possibility with the HiperFire. Great Product! Only gripe, I don't like red, please offer the finger rest in different colors.

Dan: 5/5 stars at Brownells GREAT TRIGGER RIGHT OUT There are several unique things about this trigger. First it includes a trigger shoe with it. The second being the hammer has an extra spring with it that acts sort of like a piston giving the hammer some extra power. For starter, everything about this trigger is amazing. I never really bought enhanced single stage triggers and always used the standard single stage trigger. My other builds have a two stage trigger which I like but I had one build that I wanted to keep as a single stage. The hardest part about the standard mil-spec trigger for me is the reset after you fire. It makes the trigger feel jerky because you don't know when it's going to reset so your finger is bouncing all around. Doing a slow fire with a single stage is a bit hard too because the trigger has a little bit of roughness before the hammer falls. Overall the hiperfire 24c removes the jerky pull of a single stage and allows for a smoother reset. It also gives a consistent reset so you can keep your finger on the trigger all the way. This trigger comes with three sets of springs to put in the piston behind the trigger. Hiperfire calls it light, medium-light, and medium. It gives no description as far as what the pull weight is in lbs. The best I can tell from reading the instruction is that light = roughly 3.5lbs, medium-light = roughly 4.0 lbs, and medium = roughly 4.5lbs. I put in the medium blue springs in since I wanted the heaviest weight to pull. It fits me perfectly and doesn't feel unsafe for me. Also of interest is the trigger shoe that comes with this. It is adjustable and allows you to consistently put your finger in the same position each time. It also allows you to get extra leverage as far as pulling. Personally I don't know what to make of the trigger shoe or how long it'll last on the trigger before it breaks or comes off. However, without the trigger shoe, the trigger looks like any flat bow trigger out there. Overall very good trigger. I highly recommend looking into this if you're in the market for a single stage trigger.

Link to other reviews:

Four Guys Guns

We Like Shooting

Price point:

MSRP = $235.00 

Retail = $235.00 @ Brownells

$220.95 @ Amazon

I need it now! Availability: Amazon, Brownells

Our Rating:

Pros:

  • Adjustable
  • Crisp break
  • Good reset
  • Flat bow with Hipershoe
  • Fast lock time
  • More hammer energy
  • No over travel

Cons:

  • Slight creep when the Hipershoe is at the bottom of the trigger bow

Score: 9.0 Amazing

Yes, that is a 9. 0

 

Hipertouch EDT3 trigger

The Hipertouch EDT3 trigger from Hiperfire is their newest addition to the duty line of AR15 triggers.  The EDT3 stands for Enhanced Duty Trigger cubed, It is also their 3rd addition in the Duty Line of triggers.  Hiperfire manufactures triggers for AR15 and AR10 style rifles.  Many of their triggers are used in 3-gun competitions, but this line of triggers is more aimed at law enforcement, military or anyone wanting a better trigger with the same reliability as a stock trigger.

After receiving the EDT3, I promptly installed it in one of my AR's.  Installation was extremely simple.  Basically, if you can install a stock trigger, you can install this.  The EDT3 also came supplied with a tapered installation pin.  With the pin, once the trigger assembly is dropped in the lower, all you have to do is push the install pin through the hole and follow it up with one of the supplied trigger and hammer pins.  Once installed I noticed the trigger was far better than the stock one.  Hiperfire did mention that this trigger tends to need about 200 presses before it smooths out.  I did notice it smoothed out, but it was quit good to start with.

Now for the good stuff.  The EDT3 has 2 different stated pull weights, 4+ and 6+.  Now I say "stated" because the pull weights I got were different.  Also, because theEDT3 has a unique trigger shoe, pull weights vary depending on where the trigger is being pulled.  The EDT3 comes with 2 different color hammer springs, a Red and a Green, the green being the lighter one and the red being stronger.  When the red spring was installed I measured the pull weight at 6.75lbs in the middle of the trigger and 4.5lbs on the bottom portion of the trigger.  With the green spring installed the pull weights were 5.5lbs in the middle and 3.75lbs on the bottom portion.  So now I'll try to describe the shape of the trigger bow.  The bow appears to have a standard AR curve to it, and then at the bottom 1/3 to 1/4 of the trigger it changes to flat (Hiperfire calls this a "Duplex" trigger bow).  When using the trigger I found that it lends itself to being pulled from the bottom flat portion.  I don't know if this was intended in the design, or if it just works out that way, but since the better pull weight is toward the bottom of the trigger it works out well.  In a designated marksmanship rifle, the standard curved part could be used for normal fast shots with the lower portion used for precise shots.

The EDT3 trigger is a single-stage style.  It has no noticeable creep.  The total trigger pull length, when measured at the bottom of the trigger, was 0.060".  To compare, a stock AR trigger has about 0.125" of pull, so the EDT3 has half the total pull of a standard trigger.  I only noticed the pull distance when pulling the trigger very slow from the bottom part of the trigger.  And then it was extremely smooth.  When shooting from the curved part of the trigger, I did not even notice the movement.  The reset on the trigger is also very positive, which I like.  Due to the design of the trigger, it has more hammer fall energy than a stock trigger group.  I tried it with all different types of ammunition (including steel cased) and had zero problems.

After abusing this trigger for awhile now, it has done everything a trigger should do, and does it well.  If you are looking for a replacement trigger that maintains factory safety margins and won't break the bank, look into Hiperfire and their duty line of triggers.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Duty replacement trigger for AR rifles with a lighter, but not to light, trigger pull

Target Market: Law Enforcement, Military, Home Defense, and Hunting

FNBs (Features & Benefits of this product):

  • Drop in replacement
  • "Duplex" trigger bow
  • Different pull weights
  • Single stage
  • Positive reset
  • Shorter than stock pull

What others are saying?:

Ivan Crews from Hiperfire web site:

"Yo’ll are on top of things. Got the hipertouch edt3 this morning and put it through hell. I’m x-military and this is a far better trigger group than the standard milspec. Im rough on firearms and my way of looking at things is if it cain’t take abuse I don’t need it. This trigger group can take it. Very nice feel and action. In case someone out there is wondering, this trigger group will fit and work in the colt ar 9mm and the stag arms 9mm carbines but the safety has to be removed in order to install it in the stag arms 9mm then reinstalled."

Price point: 

MSRP = $99.00

Retail = $99.00 at SWFA.com

I need it now! Availability:Hiperfire or SWFA.com

Our Rating: 8.0 Great

Pros:

  • Lighter pull weight
  • Duplex trigger bow
  • Installation pin tool
  • Great reset
  • Shorter pull length
  • Price

Cons:

  • Pull weights (only 2 options)
  • Noticeable creep when using the bottom part of the trigger

Chad’s Favorite Link: Northwest Firearms

SCCY CPX-2 Handgun Review

You may have seen the SCCY handguns and wondered what kind of gun they are; a cheap “Saturday night special” sub-par firearm or is it a real bargain, a diamond in the rough. Well hopefully after reading this review you’ll be well informed about just what this pistol is and what it is not.

So let us get into a little about the pistol. The SCCY (pronounced sky)  CPX-1 and CPX-2 are all 9mm handguns. Anyone familiar with the Kel-tec and the Ruger LCP / LC9 series pistols will be familiar with this platform, as they are essentially a scaled up version of that platform. They straddle that line between a compact and a subcompact pistol. They have a stainless steel machined barrel and slide with a polymer lower frame and an aluminum and steel fire control system that has a DAO nine pound trigger, and come in many colors. Functionally, the pistols are all the same, the only difference being the CPX-1 has a manual frame mounted safety. All come with two double stack 10 round magazines one flush fit one with a finger extension. They also come with a box, a manual, and locking device. In my six months of extensive use, I have never had to use the warranty but it seems to be one of the best in the industry. The real world street price is around $250.00

I am very blessed to have many wonderful handguns; Glock, Smith and Wesson, and Wilson Combat, to name a few. All very nice reliable accurate competition and defence guns. If they were not, I would sell them and get something else.

So why would I ever use or carry a much less expensive handgun like a SCCY? Well that’s easy, because it works! I have tested them extensively for the past six months as a defensive gun and a teaching tool for firearms instruction.

With that said, let's get into testing and evaluation. I have certain standards that my  defensive handgun must meet before I am comfortable carrying it. Dependability is, obviously, very important. This is where this budget gun shines the brightest; A++. In my six months of extensive testing with several of these pistols I don’t think I have ever had a malfunction. That’s almost unheard of. I wish that I had kept a round count but trust me it's up there. I have fed this handgun all manner of factory rounds. From FMJ and several defensive hollow points including +P+ federal 9BPLE that is rated high above the plus P pressure levels. Now, handloads are what my guns eat most of the time. I have loaded it with my competition load that is just making power factor for USPSA out of a 5 inch barrel, so I know it should be well under factory ammo levels out of the SCCY’s much shorter barrel. None of this ammo choked the gun. I have loaded from 115gr FMJs to 148gr lead poly coated bullets I have loaded them both longer and shorter than specified C.O.L. with zero malfunctions. I have fired it two handed, right hand only, left hand only, wet, dirty; I even threw one in the snow and mud and fired it without a cleaning. I have dropped it on both asphalt and dirt. Still no issues. This may upset some people but I have had Sigs and Glocks that have had more malfunctions. To put it simply: I have tested this thing for reliability and it passed.

After the gun fires, the bullet needs to hit the target. So next I'll cover accuracy. There are two types of accuracy I would like to cover. First is mechanical accuracy: how accurate the gun is with no human influences. Next, and more important, the personal accuracy: how well the shooter and the gun function together. My personal test for accuracy of my carry guns is the minimum capability to make 25 yard head shots every. This weapon  can achieve sub 3 inch groups off hand at 25 yards. The point of impact varies depending on the ammo velocity, grain, etcetera, as with any Browning type lockup, tilt barrel design. This is where the pistol came the closest of not making the cut for me. With all  the SCCY’s that I have tested the Point of impact is high at 25 yards. With the load I found that has the closest point of aim / point of impact (Federal 115gr 9BPLE) it’s still inside a USPSA head area at 25 yards, so it’s not a big issue. But with some loads the point of impact can be quite high. This just reinforces the importance of personally testing the gun and ammo you use to defend your life with. Still, these guns are capable of good accuracy; a caveat being that they have a long heavy double action trigger and that’s a hard pill for some shooters to swallow. I think double action only can be a good choice for a defensive trigger but if you are not used to it, it may take some training to be accurate. If you are used to a double action revolver trigger, it will be like an old friend.

After you have hit your target, you may want or need to hit the target again quickly. Therefore a reasonable rate of fire is important. I believe this defensive firearm with trained handler can achieve a reasonable rate of fire. For this to happen the shooter must be able to control the recoil of the firearm they are using. If the shooter has to readjust their grip after every shot, that will greatly hinder the speed of follow up shots. Now, as I stated earlier, this gun has a long heavy double action trigger. If you are looking for 1911 split times this gun, it will be slower. Also, this is a smaller, lighter gun and it has comparable amount of recoil for a gun of its size. I found the recoil substantial. More than my average carry gun. I would say more than an M&P, Glock 19, or 1911 platforms but less than Ruger LC9, S&W J frame or S&W Bodyguard. Physics being what they are, the recoil is on par with a smaller lighter 9mm.

So with the major things out of the way I will cover some other aspects of the SCCY. First off size, this handgun it about the same size as a Glock 26/27 without being as blocky, although I love my Glock 26, it’s a great carry gun I do find it uncomfortable to pocket carry. This one with a flush fit magazine I find pocketable. As a trainer I find that a lot of new concealed carriers get handguns that are too small. There are times when a super small micro .380 is all you can get away with. However for the most part a medium sized handgun in a service caliber is a more effective choice. This gun is on the “smallish” size but not to small to be effective. I feel that this pistol is a good size for all around carry.

So what’s the quality like on this sub three Benjamin handgun?  The metal on this gun is machined well, the fit and finish is nicer than you would expect for the price. The springs seem to be of a good quality with a dual recoil spring. The barrel is good quality, one note is that machine marks can be seen in the lands of the rifling. I’m not sure that most people would even notice.

Now ergonomics are in the eye or hand of the beholder. That said here are some generalities. The profile of the gun it good overall. Most shooters should get a full grip on the gun. I think the finger groves will work for most people. The Polymer's grip texture is similar to other guns. I would like to see a more aggressive texture on a CCW gun, but I would say that for the majority of polymer guns out there. The controls will be familiar to users of other modern handguns. They are in the right place and the size and shape make for easy manipulation of the pistol.

As far as the sights, go they are the standard 3 dot sights that the shooting community has come to expect. The rear is metal dovetailed with an allen set screw, a nice feature. The front it a polymer press in like the old style Glock front sights.

The disassembly and assembly are super simple, which gets high marks from me. I would say that one reason that these guns are so reliable is their simple design. I mean, they make a Glock look complicated, and the insides of a 1911 look like a super computer.

Now before you think I’m completely smitten with this piece, there are some things that I would improve. First the trigger reach is quite long. I have medium hands (I wear a medium glove). The trigger reach is on the verge of not allowing me to properly grip and manipulate the trigger. So if you have very small hands, beware. I’m not an engineer but I would think they could made a different angle on the trigger to give it a shorter reach. I took a dremel to one of mine and cut some meat out of the backstrap to shorten it trigger reach.

Speaking of dremel tooling, I also undercut the backstrap on one of the pistols to get a better bore axis and there was plenty of extra material there so I think SCCY could lower the bore axis and improve the recoil impulse. I would also lose the finger grooves.

One thing about this gun is it’s not a Glock, so the aftermarket support is not there, as far a sights, triggers, or holsters. As I said before the front sight fits in with a hole drilled in the slide and pressed in, it seems to me it would be easy to make it Glock sight compatible; thus allowing owner to customize the sights.

With all that I might change there are things I really like about this handgun.  Dependability: I can't over emphasise how rock solid reliable these guns have been for me. For a gun you may have to bet your life on, that's very important. It should be noted that this gun also has restrike capability, if that’s important to you. The next big plus is simplicity. Man is this thing is simple. The whole gun is simple and driving out two pins lets you pull out the fire control system like a Sig 320 / 250 but much simpler. Although the company does not market it as such, you could get other frames and it would be a modular platform allowing for more customization. The pistol comes with two good quality mags one with an extended grip.

Now where does this gun fit in? Well, for me, I carry a full size handgun, most of the time. I keep this one in a holster in my pack with a box of ammo. If i find myself in a situation where I can’t carry the larger gun I, grab the SCCY and I don’t feel neutered. I also don’t worry about it banging around.

For someone on a budget they can get a SCCY new, a decent knife, and a hardware store LED flashlight and have functional every day carry (EDC) kit for under three hundred US dollars. If later they want something else, keep it as a back up.

You may have seen the SCCY handguns and thought that it was probably a cheap “Saturday night special” sub-par firearm. To be honest, I had my reservations, at first but, after much testing and evaluation I have to say it’s a real diamond in the rough, and is now my go to for students who take my instruction and need a dependable handgun for training.

So to wrap up, the SCCY won't give you a crisp 1911 trigger, the customization of a Glock, or the buttery smooth recoil impulse of a Beretta 92, but for $250.00, boy it gives you a lot. More than any other gun in its class. For the price point, there is nothing else like it. This gun is truly a dependable CCW handgun that can be obtained brand new for around two hundred and fifty dollars.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:  An  Affordable CCW Handgun

Target Market: (First time handgun buyers and those on a budget.)

Key Features:

  • DAO Double Action Only
  • 10 round double stack.
  • 3 dot sights
  • Stainless steel & Polymer Constructions
  • Barrel Length: 3.1"
  • Height: 4"
  • Length: 5.7"
  • Width: 1"
  • Weight: 15oz
  • MSRP $334

What other aesthetic options or finishes are available?: These pistols are available in many colors including black, tan, red, orange, blue, pink, and purple.

What others are saying: “So, if you want a reliable, accurate, low-cost, but rugged 9mm carry pistol, all made in the USA, there’s a new name you should know: SCCY.” – Patrick Sweeney, Guns & Ammo

Price point:

MSRP = $334.00

Retail =  $250.00

I need it now! Availability: (http://www.sccy.com/dealer-locator)

Our Rating: 8.0 Great

Pros:

  • Rock Solid Reliable.
  • Good price point.
  • Simplicity

Cons:

  • Long trigger reach.
  • Long Heavy DAO trigger

SIDELOK Universal Scope Riser

The SIDELOK picatinny riser, by Kinetic Development Group, is a quick release/reattach scope riser. This riser mount is made so that removing and reattaching the mount will not effect your optics zero. They do this by some fancy cam lock system, and it works slick. One really nice feature is that this mount has no external parts sticking out the sides to get hung up on.

In order for the SIDELOK to work, one must push the squarish button in toward the mount. If the button is not in, the mount will not roll onto the picatinny rail like is required for installation. Now, to install the mount, all one needs to do is to hold it up to the rail that it is being mounted to at about a 45 degree angle, and then roll the mount on. Once on, the button will click outward and the mount will be locked on solid. The mount rolls on and off from the side that has the writing on it. If you want to remove the mount, just push the button back in and roll the mount off. The button is protected from accidentally being pressed by a "U" shaped cut-out. It also must be pushed in about 1/2" to actually get it to lock in the installation/removal mode.

I put an old red-dot that I have had for years on the sidelok mount. This red-dot needs a riser to be used on an AR style rifle, so the sidelok seemed perfect for it. I also was sure that this sight would not have any zeroing problems. I mounted the red-dot to the mount and then installed it on an AR and zeroed it at 50yds. I then took it back off and on. Shot some more with no signs of zero shift. I must have removed and replaced the mount and sight probably 20 times that day. Some because I wanted to test it, and others to show people at the range how cool it was. At the end of the day I was still shooting the same place as I was right after zeroing the red-dot. In the time I have had the Sidelok mount, I have removed it plenty of times just to show people. I once even put it on backwards, you can put the button facing forward or backwards, whatever will work best for you. I even beat on the rifles pistol grip, for a different review, and still no zero change.

This SIDELOK mount is probably the best riser mount I have used. The ease of use and the fact that it holds zero make it perfect for someone who is changing optics often. It raises the mount up 0.62" from the top of the rail it is being mounted on. And it gives 3.5" of usable picatinny rail. It is 4.33" total length when locked on and is 1.1" wide total. Kinetic Development Group has done a great job with the Sidelok family. They are also available as dedicated mounts for the Aimpoint Micro, PRO, C3, and Comp M4.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Quick attach riser optics mount that maintains zero.

Target Market: Anyone looking for an easily removed and installed optic mount.

FNBs (Features & Benefits of this product):

  • Quick attachment
  • Quick removal
  • Easy to use
  • Solid lock up when installed
  • Zero point of impact shift
  • Lightweight at 3.4 oz

What other aesthetic options or finishes are available? None, Black is it.

SIDELOK Aimpoint Micro

SIDELOK PRO/C3/Comp M4

What others are saying?: Google was no help and so none were found

Price point: 

MSRP = $99.00

Retail = $99.00 @ Brownells

I need it now! Availability:Kinetic Development Group and Brownells

Our Rating: 8.5 Great

Pros:

  • Quickly attaches and removes
  • Holds zero
  • Mount is extremely sturdy
  • No knobs sticking out the sides

Cons:

  • It is a riser mount (Reaching for stuff, I know)
  • Price
  • Would be really nice if it came in an option for magnified optics (Something like the Warne Mount)

Chad’s Favorite Link: U.S. Tactical Supply

Lucky 13 Bullets Review

During my work as a firearms instructor I am blessed to come across all kinds of guns gadgets and ammo. Being a gun nerd, rarely am I surprised by a product or piece of equipment.

However, that’s precisely what happened when a man stepped up to the firing line with green bullets! They were unlike anything that I had seen before. I had seen poly-tipped bullets, even ammo with partially polymer cases, but nothing like these projectiles. Naturally, I struck up a conversation with the fella to discover just what these strange “alien” bullets were all about.

The shooter told me they were plastic covered bullets from a company called Lucky 13. Upon inspection, I discovered just what these bullets were, and what made them so unique. So what are they?

These bullets are, in fact, a lead bullet that is completely encased in a thick polymer jacket. That’s right plastic jacketed bullets, crazy! Naturally I had to get some. So I went to lucky 13 and ordered a few hundred in green, just because. Plus, if there is one thing recent marketing has taught us, it's that green kills zombies better.

I got 148 grain round nose for my .38 special and 9mm They arrived shortly after and I really got to play with them.The bullets start out there life as a traditional cast lead bullet. Then by some process unknown to me, they get coated in a polymer jacket. The jacket comes out quite thick, thicker than a copper plating or even some jacketed bullets I’ve seen. It’s also quite tough. You're not going to scratch it off with a fingernail; you would be hard pressed to get it off with a knife. So initial impressions were good. Still I couldn't care less how they look if they don’t load and shoot well.

I first loaded them in .38 Special. I was unsure if I was supposed to use cast lead data or jacketed bullet data, so I called the company and a real live person, in America, supplied me with the correct loading data. I suggest you obtain your data the same way. I tinkered with .38 loads with 700X and titegroup powders. I also later loaded 9mm loads with the above listed powders. The bullet loading process is more like a traditional cast lead than a FMJ. My cases had to be flared out more than I like and if it were my design on the bullet, I may have used a different angle on the bottom of the bullet to help them seat easier.

The bullets performed admirably with all my test loads in both revolver and semi-automatics. They gave me no more malfunctions than FMJs. In fact, I had zero malfunctions of any kind that I can think of; even at the lower and upper end of the loading range. They perform more like cast lead bullets than FMJs as far as live fire, with one big difference. If you have ever loaded and shot lead bullets you know about barrel leading. To my delight, when I went to clean my handguns, there was no lead fouling or residue, or even plastic residue. I did not see any bullet residue of any kind. There was still, of course, powder and primer residue. Even so, they are much cleaner than lead bullets.

So what’s the verdict? Well only time will tell, you might be thinking "Plastic bullets: who needs them?" Well, may I remind you that people thought the same about plastic guns in the 80’s and 90’s and now they are the biggest part of the handgun market. The price is right and with any new technology it will probably improve and the prices may even get better. They are target bullets and not intended for defense (not to be confused with the Polycase Inceptor). Who knows what, if any, effect the polymer jacket would have on terminal ballistics. While I don’t think that these will render full metal jackets obsolete, and "Full Plastic Jacket" is nowhere near as cool for a movie title as "Full Metal Jacket." I would definitely use them over traditional cast lead and lubed bullets. I would even pay a little more for the poly-case. I think there is room for improvement and a wider array of products and designs but like I said it’s all fairly new. Lucky 13 seems to be a good, American company, that makes a good, innovative product at a more than fair price.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Affordable FMJ substitute

Target Market: Handloaders

FNBs (Features & Benefits of this product):

  • Coating reduces barrel fouling.
  • Less lead exposure.

What other aesthetic options or finishes are available?: The green is unique.

What others are saying: http://www.ncgunowners.com/forum/showthread.php?tid=11358

Price point:

MSRP = $42.00 per 500 9mm

I need it now! Availability: You can get the Lucky 13 Bullets directly from their website. 

Our Rating: 7.0 Good

Pros:

  • Good price point.
  • Uniformity and Quality.
  • No bullet residue

Cons:

  • I would like to see more options.
  • The bullets should have a better taper on the bottom to help seating.

V Seven Hybrid 3 gun / Sport Selector Review

After receiving the V Seven Weapon Systems hybrid ambi safety selector for review, I immediately noticed how nicely machined it was.  V Seven is an AR parts manufacturer that makes high quality parts for AR-15 and AR-10 style rifles. They also make lightweight parts using titanium and aluminum, or a combination of these, like in the Hybrid 3 gun sport selector.  This safety selector is not your run of the mill Ambi safety selector.

The V Seven Hybrid safety possibly gets its name because it uses a titanium core (The part that goes through the receiver) and aluminum levers. Or it could be because one can change the amount of throw the safety moves.  In this case one can choose to run the safety in a 57 degree throw, or the normal 90 degree throw.  I found the 57 degree throw to be quicker and easier than having to rotate it 90 degrees.  To convert between the two options, one must first remove the pistol grip as this holds the detent and spring for the safety.  Then one of the levers needs to be removed off of the core.  This is done using a #10 torx driver.  After removing one of the levers you can remove the safety from the receiver. Once this is done, you can swap the core around to get the desired throw amount.  If you don't think you can swap the safety yourself, I am sure your local gunsmith would do it for a small fee. After installing the safety, don't forget to safety check it for function.

As mentioned before, this is a hybrid safety.  The inner core is made from titanium and has a black ion bond coating on it. The levers are made from hard anodized 7075 T6 aluminum. Speaking of the levers, the left side one is standard length, or maybe a hair longer, while the right side is a shorter than normal lever.  These levers are wider than standard and have a texture that resembles a mountain bike or motocross peddle.  It has sharp points on the inside and outside while being machined out in the middle.  This gives a very noticeable feel to the lever.  I was actually still able to feel the safety with gloved hands. However, this sharp texture may be too much without gloves, so you may want to toughen up that thumb. The safety has great feel to it when rotating it off and on.  The detent is extremely well machined with zero slop when engaged.

If you are looking for an upgrade to your stock safety lever, this is a great option.  Or if you are trying to lighten up your AR, this might be a good option also as it weighed in at 0.30 ounces on my scale and V seven states it weighs 9.77 grams (0.345 ounces).  I am very pleased with the V Seven hybrid ambi safety.  It is a great product at an affordable price.

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Convertible ambidextrous safety for AR style rifles. Converts between 57 and 90 degrees.

Target Market: As mentioned in the product name, 3-gun. But also anyone looking to upgrade to an ambidextrous safety for their AR.

FNBs (Features & Benefits of this product):

  • Convertible between 57 and 90 degree throws
  • Ambidextrous
  • Lightweight
  • Corrosion resistant
  • Lifetime warranty
  • Made in U.S.A.
  • Comes with safety detent and spring

What other aesthetic options or finishes are available? None, just basic black.

Can be had in non-ambi in 57 or 90 degrees

What others are saying?:

Kelly on Vertexops.com 5/5 stars

I can't say enough good things about this safety it works very smooth and clean movement and the lightest one i have found. I will be putting one of these on every build i do.

Johnny Review on Northwestfirearms.com 5/5 stars

There are very few AR manufactures that I have tried that I could recommend and give a 5 out of 5 stars to, but V-Seven Weapon Systems is certainly one of them. V-Seven is the common cure for the AR without a doubt.

Price point: 

MSRP = $63.00 @ V Seven

Retail = $61.11 @ Vertexops

I need it now! Availability:V Seven Weapons or Vertex ops

Our Rating: 9.0 Amazing 

Pros:

  • Lightweight
  • Ambidextrous
  • Convertible between 57 and 90 degrees
  • Solid feel
  • Wider than normal levers
  • Beautiful machining

Cons:

  • Sharp feel
  • No included torx wrench

Chad’s Favorite Link: Oregon Firearms Federation

AmmoBot MK1 Autoloader Review

About me: A far cry from some other reviewers, I do not use this machine in any business capacity. I'm an avid USPSA and 3-gun competitor, and shot approximately 25K rounds of 9mm and 5K rounds of .223 this past 2015 season - all loaded on my S1050, pulling the handle manually. Here are one shooter's thoughts so far...

I'm really enjoying my AmmoBot. I've not had it terribly long, but long enough to know I should have bought it sooner! Overall, it's incredibly simple to set up and operate. I'm far from a mechanically capable person, so when I had a few sub-basic questions, the owner was very responsive and helpful. I think I was up and running in under an hour after unboxing the gear.

I've had the occasional hangup while running, but really, nothing would have been different than if I was still pulling the handle manually. One 9mm case somehow got on to the shell plate upside down from the case feeder. At the resize station, the decapping pin poked right through the primer, but when the die made contact with the case, the machine stopped and when it sensed a short stroke, halted. At that point, I took the case out of the priming station since it hadn't been swaged, and moved the rest back one position. The case that was in the crimp station did get pushed into the completed cartridge bin, but was easy enough to find and put back to the correct station to be completed. That's a lot of words in a big paragraph to talk about the details of one of the only stoppages I've had in my first 6K rounds of 9mm loaded in the last month.

Also, at first I was a little nervous about the handle left on the machine and in full swing. I was put at ease quickly during my first session loading. I basically stand one step to the left of the machine watching the powder drop, to know for certain it's reaching full stroke, and watching to verify bullets are not dislodged between the dropper and rotating to the seating station. I've lost probably 5 or less bullets (out of 6,000) and because I was in place to see it, hit the hand-held stop button so I could hand place a bullet before the downstroke for seating was completed. I've run the machine at almost 2200 rounds per hour, which really tired my eyes. I typically run between 1600-1800, have no issues at that speed, and it's easy enough to stop if something looks "off".

The second reason I was happy that the handle was still in place was this past week, when I decided to shoot in the limited division for the first time in two years, but had no ammo loaded. Since I haven't received my Mr. BulletFeeder .40 conversion yet, I was able to pull the handle manually and load enough ammo for the match. It's also helpful to have for set up and tuning the powder drop before getting in to a full loading session.

It was actually a Brand "M" auto-drive that initially got me wanting one. It looked fancy, cool. The more I researched though, the more the AmmoBot stood apart in many ways. The infinitely adjustable speed for one, not using one of three pre-set speeds. The ease of use was the second thing. Sometimes you want to pull the handle for one reason or another and not let some computer take the feel out of the system. Finally the incredible value in the AmmoBot. At the current price point, I was able to purchase the AmmoBot and 22,000 of the 9mm projectiles I shoot in matches for the price of the other autodrive I considered.

All in all, I'm extremely happy with my purchase. The owner of the company is incredibly responsive and helpful when questions arise, and the fact that they are constantly developing new advancements and offer them as retrofit purchases to current users speaks volumes for their customer service.

*Note: The "owner" Alex is referring to is Jason Pruett.  He's not the owner, but is the person that interfaces with the customers.  There are several individuals on the AmmoBot Crew.  Everyone contributes and does a really good job of making Jason look good with the customers.

IMG_1768.jpg

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Great value, easy to set-up and operate automation machine for Dillon Super1050 reloader without making permanent modifications.

Target Market: Competitive shooters, bulk reloaders, small to medium Ammo companies

FNBs (Features & Benefits of this product):

  • Easy set-up: Up and running in approximately one hour.
  • Easy to use: no complicated programming needed at all.
  • Smooth operation: more consistent and accurate ammo produced.
  • Save your rotator cuff from pulling the handle thousands of times per month.

What other aesthetic options or finishes are available?: Comes powder coated Dillon Blue to match your machine and accessories.

What others are saying?

AmmoBot.us User Submitted Reviews

Price point:

MSRP = AmmoBot MK1 $1,195  + $1,739 for the Dillon Super 1050 + $469 for the DAA Mr. Bullet Feeder = $3,403 total

Retail = Starting at $2,995 at Immortal Arms for complete packages!

I need it now! Availability: 3-4 week lead time.

Our Rating:

Pros:

  • Value, one of the least expensive autodrives available.
  • Ease of use
  • No modification to your Dillon Super 1050 at all
  • Infinitely adjustable speed controls
  • Incredibly consistent ammo product. (Extreme spread reduced from avg of 15-20fps to 5.5fps)
  • Speed - Load upwards of 2200 rounds per hour! If you can keep up filling the components.
  • Constant Innovations: Dual speed control to separate forward and reverse; .45ACP small primer detection and flipper; quieter drive motor.

Cons:

  • A little loud, but I wear ear phones and listen to gun podcasts while loading. **New version of drive motor has significantly reduced noise.

Score: 9.0 Amazing

Alex Melnichak - Immortal Arms - Purchased 8/10/2015, Reviewed 11/27/2015

To contact the author Alex, feel free to visit his competition shooting page on FaceBook.

Bigfoot Gun Belts Untamed Leather Belt

It's about time we take a look at an often neglected piece of gear that makes such an impact on how to carry yourself, as well as your firearm. I'm talking about belts, and I'll admit that I had been wearing a sad excuse for a leather dress belt everyday even when concealed carrying. That belt, which probably cost me under $15, was sagging badly after just a month of use. When it sagged under the weight of my handgun, I would just resynch it higher and tighter even if it was uncomfortable. I just didn't know any better.

Luckily I saw the light, as a belt manufacturer sent me an actual gun belt to review.Bigfoot Gun Belts is a new company specializing in premium high quality gun belts. Hidden in the Pacific Northwest and embracing the Sasquatch culture, the company claims "Bigfoot may be difficult to find, but tracking down a quality gun belt has never been easier." Similarities drawn between their product and the creature itself are  1) They’re both born and raised in the Inland Northwest, 2) They are both unbelievably strong, and 3) They both smell... Bigfoot reeks of tree sap and sweat, and their gunbelts smell like genuine cowhide and rich dyes. While its an unconventional marketing angle, I find the tongue-in-cheek brand statements from this new company to be a refreshing change in an industry saturated with puffy chested soldiers of fortune or clueless models with horrible trigger discipline.

Currently at the time I'm writing this review, Bigfoot's Untamed series features three different belts: the 14oz Leather,14oz Leather + Steel Core, and 18oz Leather + Steel Core. The steel core belts feature a core of stainless spring-Steel embedded between two layers of English Bridle leather. Much like the Alien Gear Cloak Tuck 3.0 Holster, the addition of a spring steel core provides added strength to retain the belt's shape without adding excess rigidity and thickness. This core reinforces the leather and keeps the belt remaining level around your waist even with a holstered gun pulling down on one side, which is ultimately leads to sagging and a premature death for every other gun belt over time.

The leather craftsmanship is noticeably fine on the Bigfoot Gunbelt, as its double layered, drum dyed, stitched with military-grade thread (Tex 270), and beveled, burnished, and painted on the edges for a smooth uniform finish. Honestly this is one of the first belts that looked just as nice on the inside as on the outside. The extra care and craftsmanship to the edges and the stitching lead me to believe this belt won't fall victim to layer separation as my other belts, or degradation of the underside that compromises the top finished layer.

The hardware on the Bigfoot is nickel plated for corrosion resistance, and the roller buckle was chosen to allow the belt to effortlessly ‘roll’ through your buckle without superficially marring the leather at all. While I'm not a huge fan of roller buckles, because of the loose jingle when not fastened around your waist, its ease of use and low impact on the leather's surface are hard to not love. If you're the kind of lad or lady who has a lucky belt buckle you cannot live without, good news! The Untamed Gunbelt has two easy to use snaps that release the roller buckle and let you install your own buckle. Just be warned, it's lucky longevity will be tested now that it's on an authentic gun belt built to last.

Now that I've worn a Bigfoot Gunbelt everyday for over a month, I've since retired my other belts to keeping sleeping bags rolled up in storage. As someone who carries a firearm for security and confidence in the real world, I'm really glad I've finally experienced a secure belt that keeps my pants up better than ever before. The steel core of the 14oz Leather Untamed Gunbelt adds robustness and retain the original vigor of the belt. Whether your everyday carry is inside the waistband, outside the waistband, or you have the legend Sassy himself as your bodyguard but need to keep your britches up, give the Bigfoot Untamed Gunbelt a try. You really don't have much to lose, as every Bigfoot Gun Belt is backed by a 7-Day Test Drive and Legendary Warranty, meaning if you’re not fully satisfied by this beast of a belt, send it back to Bigfoot for a full refund.

Firearms Insider Reviews – 8 Key Points

Claim to Fame: The 14oz. Leather Gun Belt provides superior support to your everyday carry. Once you feel the strength of this gun belt, you’ll never want to wear a regular belt again.

Target Market:  Concealed Carry and Open Carry

FNBs (Features & Benefits of this product):

  • 1.5 inch width
  • 14oz. of leather cut to the exact specifications of carrier
  • Military-grade polyester thread (Tex 270) stitching
  • Two layers of English Bridle leather
  • Nickel-plated roller buckle w/ two sturdy snaps
  • Snaps provide an easy way to switch out their buckle for another within seconds
  • Triple Edge Finish: in-house bevel, burnish and paint
  • Once assembly is complete, our iconic Bigfoot logo will be pressed into the inside of your leather belt.
  • 7-Day Test Drive and Legendary Warranty - ( if not satisfied, send it back for a full refund)

What other aesthetic options or finishes are available?: Black, or Rich Brown

What others are saying?: "A new gunbelt I recently purchased is superb, so I thought I'd mention it here. I was in the market because I felt like I needed a thicker and stiffer gunbelt for open carry purposes, than the 1.5" Galco horsehide gunbelt that I was using.

Bigfoot Gun Belts has a new technology for gunbelts in that it has a steel core between 2 layers of high quality bridle leather. I ordered the 14 oz. with steel core version in brown (they make the same belt without a steel core, and also an extra heavy 18 oz version with steel core). The picture below shows what the steel core looks like.

What I was impressed with is that the inside surface of the belt is finished with the same quality as the outside surface; and the steel core really helps to keep an open carry pancake holster tight against the body. Bigfoot gunbelts is a newish company in Northern Idaho, and the price for a top quality gunbelt with steel core is less than competitor's similar belt without steel core ($59.88 + shipping). Also, they bevel the edges smooth after putting the 2 layers of leather together--a nice touch. The thickness of the gunbelt is ~1/4" and it is 1.5" wide. Great belt that will last for decades." - SilencerTalk Forum User

Price point:

I need it now! Availability: Bigfoot Gun Belts

Our Rating:

Pros:

  • Leather grade is impressive
  • Edges are treated to prevent wear and deconstruction
  • Inside is given as much care and quality as outside
  • Tapered belt end makes easy for pant looping
  • Two snaps make it easy for different belt buckle options
  • Steel Core models hold their shape longer than any other belt

Cons:

  • Roller on buckle is the only part of the belt I think could be built better, but I'm splitting hairs

Score: 8.0 Great

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast

Hunter of Design

Safeguard Armor Level IIIa Soft Body Armor Test & Review

Body armor is a hot topic of discussion these days. The market seems to have exploded lately with discussion about which plate carriers and rigid armor plate is the best for stopping high level ballistic threats. Most of these hard armor plates are rated to stop direct hits by high powered rifles such as 5.56 and 7.62x51mm. However, the soft body armor worn to stop rounds fired from a pistol or submachine gun are still available and worn by many police officers every day.

SafeGuard armor recently asked the Firearms Insider to test one of their ballistic panels. I agreed to do the testing and SafeGuard sent along to me a Level IIIa soft ballistic panel. The level IIIa is the rating used by the National Institutes of Justice (NIJ) to rate the level of protection the vest offers. Level IIIa must be able to stop 9mm FMJ 124 grain at 1,400 fps as well as .44 Magnum 240 grain at 1,400 fps. The ballistic panel itself was made out of a nylon-type material that enclosed at least 100 if not more layers of bullet resistant material. I informed SafeGuard that I would not be able to perform a test that conformed strictly to the NIJ standards, but that I had shot at ballistic vests before and knew how to perform a pretty valid and interesting test.

I started with obtaining a bunch of different cartridges to shoot at the vest. I sourced a 110 grain .30 Carbine, two full power .357 Magnum 158 grain Semi-Wadcutters, a 9mm 124 grain standard pressure and a 9mm 124 grain +P load, a 50 grain Liberty Defense 9mm load, a 7.62x25 Tokarev surplus load, as well as .22 Magnum 36 grain Hornady V-Max and CCI 40 Grain Maxi-Mags. For the test I shot the vest with the 9mm 124 grain load and the .357 Magnum load out of a 2 and ½ inch S&W revolver to show the control shots, that the vest could do what it was rated for. We then went through all the various cartridges that were assembled, to torture the vest and see what it could stop. One particularly interesting test was firing the .357 Magnum rounds out of a snub nosed revolver, and then out of an 18" barrel single-shot rifle. It stopped both, even with the increased velocity from the rifle barrel. The vest was shot multiple times in multiple different places while braced against a solid cardboard box with gallon jugs of water inside the boxes.

The vest performed way above what it was rated for. It stopped every single round except for the 110 grain .30 Carbine out of the M1 Carbine. That round is traveling around 1,900 fps and pierced clean through the vest. I was very very impressed with how the vest performed, especially after being hit repeatedly so many times.

At the end of the test, as you can see on the video, we took 12 individual layers of the bullet resistant material and clamped them to the box. We were curious how few layers it would take to stop a .38 Special 125 grain +P bullet. We fired that round dead center from a S&W Model 36 snub nosed revolver and the bullet was stopped by the 12 layers. It goes to show just how strong only a few layers of that material can be when stacked one on top of another.

The video above shows in great detail the entire test, as well as the bullets at the end after they are pulled out of the vest. I am very very impressed by the Safeguard armor vest, and would put it on the top of my list when shopping for body armor.

Visit SafeGuard Armor Here

How Body Armor Matches Up


Listen to Handgun Radio

VLTOR MP-1 Modpod

modpod-1.jpg

A stable rest is an imperative to shooting a firearm accurately. It doesn't take a rocket scientist to figure that out. There are several pieces of gear meant to address this, between shooting bags, benchrests, and bipods - both attached to the firearm or separate. The advantages to attached bipods are purely convenience: it travels with the rifle, easy to deploy, and rock solid.

While Harris style bipods are the current standard for weapon mounted bipods, they are not the end all be all. They typically mount to the bottom of the forend, via a sling swivel stud or a 1913 picatinny rail with an adaptor. The legs fold at a 90 degree angle (typically parallel to the barrel) when not in use, and fold down to a perpendicular angle.  The legs typically extend via manually pulling or a button press, and collapse either by a button, pressure, or a combination of both. The weaknesses to this design is discomfort when slung behind the back, as the bipod edges dig into the shooters back or shoulder, requiring an alternate sling mounting option. Another negative is the loss of real estate under the forearm which could be used for grips or lights, and they limit how low your rifle sits to the ground, which translates to increased muzzle rise during recoil.

With the proliferation of modern sporting rifles and tactical rifle chassis with picatinny accessory rails, bipod designs have adapted to also be modular. One such bipod is theTangoDown ACB-4 bipod. The ACB-4 Bipod was engineered specifically for current M16A4/ M4 / MK 11-type rifles with minimal ergonomic or weight impact. Constructed of light weight aluminum forgings and advanced polymers, the ACB-4 attaches directly to any picatinny 1913 rail and folds closely to the weapon for a low, snag-free profile. It can also be used with the BPM-1 adapter, which takes attached to the swivel stud of most bolt action rifles.

The VLTOR MP-1 ModPod is variation of the TangoDown ACB-4 bipod system. The ModPod comes as two separate legs constructed of polymer that mount to rails on either side of the forearm/handguard in the 3 and 9 o’clock position. The advantage to this configuration is the legs can swivel and lock in a detent every 90 degrees. Than means they fold up along side of the barrel in either direction. Thats right, depending on the length of your handguard, you could possible have the legs fold toward the shooter, or traditionally away from the shooter when not in use. This leaves the bottom portion of the firearm's forend free for sling attachment, grips or other accessories (M203 Grenade Launcher, anyone?) The bipod feet are also nicely designed, like a duck foot with aggressive texture underneath.

The disadvantages to this VLTOR design are three fold. First, it's much slower and clumsier to deploy. First, the large diameter buttons on each leg are easy depress and its possible to do with only one hand, but you still need to pivot each leg into the desired position individually. You could use both hands and operate both legs simultaneously, but the rifle would have to be resting on its butt, or slung perhaps. Secondly, each leg's length adjustment is very small - only 2.5 inches total. Most bipods are usually 9"-13" in adjustment and longer in different variations. Not to mention the adjustment of each leg does require both hands to adjust, you have to press hard against an oval button with one hand and pull the leg in or our til the button pops into the next slot. The third issue which is minor and differs between what rifle you intend to use... is the large round axis point that protrudes up into the area of the top rail. This can interfere with certain flip up iron sights, lasers, and other accessories. Mounted to my AR-15 with a Parallax Tactical FFSSR handguard, the axis points actually contact the Magpul MBUS front sight. A different front sight would solve this, but to me the button diameter of the ModPod is a bit larger than I think it really needs to be.

With those issues pointed out, you may be wondering why even bother? Considering the price of about $180 retail, I might tend to agree with that question. Only 4 inches of adjustment, the ModPod is an extremely short rest, but that's its greatest strength. I see the ModPod specifically intended for modern sporting rifles AKA defensive rifles, or assault rifles if you are military or law enforcement and have the pleasure of enjoying select fire. Rifles like the FN SCAR, Bushmaster ACR, M4 Carbine, M249 SAW, and other railed firearms that would benefit from a low profile bipod that folds along the body/barrel. You could attach these to a AR Pistol, SBR, carbine length, mid length, or full rifle length platform. Heck, you could even attach the ModPod to AK47/74 type rifles with the right handguard setup.

The modular capabilities of the VLTOR ModPod are its key selling point, for low prone shooting or benchrest shooting. In a combat theater, the low profile of the ModPod is more advantageous for snag-free concerns as well as keeping the shooter lower and less exposed. With a bolt action rifle sporting a tactical chassis (or just frankenstein bolt rail sections into the forearm) these bipod legs are great as well. My intent and purpose for buying this bipod was to install on a Remington 700 with a Magpul Hunter chassis (when they finally ship!) for the simply comfort of carrying when slung. I will update my review with pictures as soon as I have them installed.

Firearms Insider Reviews – 8 Key Points

Claim to Fame: The MP-1 Modpod has individual bipod leg that attach to side rails, allowing the user to have an unobstructed lower rail.

Target Market:  Modern Sporting Rifle owners, Long Guns w/ Chassis

FNBs (Features & Benefits of this product):

  • Mounts to any weapon that features a 3 and 9 o’clock position Picatinny railed handguard/rail system
  • Legs rotate 360 degrees, locking every 90 degrees
  • Simple and silent push button operation for each leg
  • Self-contained hardware with no small part to lose
  • Allows for the use of an M203 Grenade Launcher, forgrips or lights/lasers
  • Feet are adjustable for three different lengths
  • Impact and temperature resistant polymer
  • Matte anti-reflection/anti-glare finish
  • Weight: 10.6oz
  • Length collapsed (from centerline of pivot): 8.430 inches
  • Length extended (from the centerline of pivot): 10.940 inches
  • Metal components are both stainless steel and aircraft-grade aluminum

What other aesthetic options or finishes are available?: Black, Flat Dark Earth

What others are saying?: "EXPENSIVE BUT WORTH IT. Love this bipod system. I use this on my M4 with excelent results. Yes they are polymer but in reguards to this product that is a positive, the material is strong yet light weight, and easily withstands heavy recoil. This bipod also gives you the ability to rotate in place slightly without changing postitions. I will be buying another one for my hunting rifle as I think it would work out well." Brownells User Review

"Great bi pod. I use a lot of my rail space for other things so to save space is essential to me. Awesome sleek low pro look too. My only complaint is that one side seems to be looser then the other. I can't find a way to tighten it but it works fine. I would definitely recommend it." Amazon User Review

"4 stars: Very nice bipod arrangement. I took a star away for being overpriced. I mounted it so that when folded back it tucks nicely in above the side rail." Amazon User Review

Price point:

I need it now! Availability: Brownells, Amazon or many online stores

Our Rating:

Pros:

  • Silent operation, rotates every 90 degrees
  • Frees up bottom rail or stock area, more comfortable when slung over shoulder

Cons:

  • Two handed operation of telescoping legs for both expanding and collapsing
  • Wingnut style thumbscrew gets in the way of some top rail mounted accessories
  • Way overpriced in my opinion for its function and material

Score: 7.5 Good

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast

Hunter of Design

Magpul MS4 Single QD GEN2 Sling

It's no secret that I'm a Magpul fan. Hanguards, stocks, grips, you name it - most of their products have become the bar to which other competitors are measured, and thats a widely held opinion - not just my own.  That said, I've actually never tried one of their sling products before, but have tried many other lower cost slings on AR-15 and AK47 platforms. I used to think a sling was pretty basic and ubiquitous, not something worth spending more hard earned money on if they serve the same function and don't get much use shooting from the bench anyway. That is, until I picked up the MS4 Dual QD Sling GEN 2.


Magpul's Multi-Mission sling was designed to give a versatile weapon-retention solution for a multitude of tactical environments and missions. The MS1 sling system started as a dedicated two-point sling that also works as a one-point sling when using optional adapters. As a standalone product, the rapidly-convertible MS3 allows an operator to leverage the maneuverability of one-point attachment for direct action, or two-point attachment for stability. Single-hand adjustments and quick-release, positive-locking hardware provide flexibility and durability in a truly adaptable sling system.


Used in conjunction with the Magpul ASAP® plate (sold separately), the MS3 enables seamless transitions into an array of shooting positions without getting bound or fouled. The MS3 concept allows switching from Weapon Shoulder to Reaction Shoulder for shooting around corners, under vehicles, or to minimize exposure. The MS3 can also increase operator survivability by keeping the weapon in the fight in case of injury to the operator's shoulder, arm, or hand. The MS3 GEN 2 incorporates a new low profile quick-adjust Slider which minimizes bulk and allows for secure, yet effortless, sling adjustment. Webbing length has also been increased for a comfortable fit with all body types and armor configurations.now features QD swivel mounts on both ends, with QD sockets on a D-Ring allowing for quick transitioning between one point and two point configurations.


Some rifles are more comfortable to carry slung over the shoulder or across the back, but single point slings are better for when the firearm needs to be at the low ready. The modularity of this sling system, coupled with it's simple one handed length adjustment, make it nearly perfect in my mind, and easily worth the investment... especially if you have multiple rifles, shotguns, carbines, or other firearms that all have QD sling attachment points. After my first, I had to pick up about 3 more of these in each color because I like each of my rifles to have a dedicated sling that flat out works and will outlive me.

Firearms Insider Reviews – 8 Key Points

Claim to Fame: The MS4-QD GEN2 is designed for easy, rapid convertibility between one-point and two-point mode.

Target Market:  Modern Sporting Rifle owners, Military / LEO, 3-Gun competitors

FNBs (Features & Benefits of this product):

  • Heavy-duty push-button QD sling swivels for both one and two-point attachment
  • Durable, precision-cast, Melonite finished steel QD D-Ring allows for quick transition from one to two-point mode
  • D-Ring finished with Melonite for resistance to wear and corrosion
  • Custom 1.25 inch wide nylon webbing material is wear resistant and anti-chaff
  • Low-profile adjustment Slider for adding or removing sling tension with a single-hand
  • QDS Sling Mounts compatible with buttstocks, end plates, receivers, and hand guards that have a QD sockets as well as the Magpul ASAP®-QD, RSA®-QD, MSA™-QD, and shotgun Forward Sling Mounts
  • Colored webbing has Near Infrared (NIR) treatment to reduce IR signature

What other aesthetic options or finishes are available?: Black, Stealth Gray, Coyote, Ranger Green

What others are saying?: "In training we used a "cheaper" sling and I'm glad the Magpul sling feels nothing like the Blackhawk slings. It is much easier to adjust for first time setup and during use. The components are high quality and look great on my S&W M&P 10." Amazon User Review

"Very nice sling!!!! I have been shopping slings for years til i found this one. Awesome Single and Two point sling fulfills all firearm sling needs in one easy to use very adjustable sling. One hand quick slide adjustment make the transition from single to two points seamless and easy. Outstanding MADE IN THE USA Magpul high quality. It may be a bit pricey but in my opinion VERY worth it." Amazon User Review

Price point:

I need it now! Availability: Brownells or local gun shops

Our Rating:

Pros:

  • One handed adjustment is easy without lengthy tab or loops to pull
  • Perfect for rifles with QD in stocks and on handguard
  • Quality steel parts, no rubbish plastic to wear out quickly

Cons:

  • Price is steep compared to most other slings (but well worth the quality IMHO)

Score: 8.5 Great

Featured FFL:

For FFL services I choose Promised Land Firearms in Toulon, IL.

Ryan's Links:

Gun & Gear Review Podcast

Hunter of Design

Lone Wolf Dist Compact Timberwolf Frame Review

While attending the NRA Annual Meetings in April of 2015, I got to meet up with Zack, the marketing manager of Lone Wolf Distributors. I was really interested in their Compact Timberwolf Frame for Glock pistols. Through our conversation, Zack agreed to send me a fully built Timberwolf Compact pistol, which I have since purchased. This is part one of two, where I focus on the frame. Stay tuned for my review of the upper assembly, as well as a summary of the pistol as a whole.  20151024_180117-1

Lone Wolf Distributors has been manufacturing accessories and replacement parts for Glock handguns for many years. From slides, barrels, triggers, and more, you could almost build a custom Glock by just using Lone Wolf’s parts. The only thing missing was the frame, until somewhat recently. Lone Wolf saw the modifications that people generally made to their standard Glock frames, and decided to offer a lot of these modifications right out of the box, with their Timberwolf frame.

Common modifications made by end users to Generation 3 Glock pistols include backstrap reduction, frame texturing, adding extended magazine releases, and even removing material in key places to allow a higher grip on the handgun. Well, Lone Wolf Distributors took all of these modifications into consideration, when designing their Timberwolf frame. I will take a look at each of these aspects one-by-one.

Grip

20151024_180401

One of the biggest benefits to this replacement frame would have to be the grip. The Timberwolf offers two choices of backstrap to the shooter. The first is the slim grip. It is an incredibly short (front-to-back) grip that more closely matches the grip angle of the classic 1911. The second is a swelled backstrap. It is a little smaller in the hand than the standard Glock swell, which will come as a welcomed feature to many Glock owners. This setup happens to be my favorite of the two. As good as it feels, the smaller grip leaves the meat of my palm really close to the magwell, and it can actually get pinched in between the magazine base plate and the frame, upon reloading. Do this a couple of times, and it starts to get on your nerves. Luckily, the swelled grip fit me just as well, if not better, and Lone Wolf engineered the swap very well. To make the change, all you have to do is, with an empty gun, insert a flat tool into a slot that can be accessed through the magwell, and gently pry downward.

12170749_512874168870584_609558428_n

In my trials of the differing grips, I noticed an odd, but very well thought out (and well hidden) feature. Under the backstrap is actually a round recess that will hold one CR2032 battery, which is the somewhat industry standard for micro red dots. Alternatively, it can hold two CR2016s. This is a great feature if you’re building a race gun, or just want to carry a gun with a dot sight, and I am honestly a little shocked LWD doesn’t even list this in their feature literature.

The next part of the grip is the texture. Many people feel that the Gen 3 Glock grip is just too slick. I, for one, am in that boat. What the Timberwolf offers is a very aggressive square pattern, without being so harsh as to tear up your hands, with one exception. The edges of the frontstrap have slightly sharper corners than the rest. I suppose that is just a geometry issue of the curve meeting the corners of the texture, but it became very uncomfortable for the end of my pinky. That being said, it could easily be taken care of with a quick pass of some fine sandpaper, just to knock the edge off. Overall, the grip texture is very good at keeping the gun in your hands while firing. Speaking of the frontstrap, one feature many owners elect to remove on factory Glocks is the finger grooves. The factory finger grooves on a standard Glock 19 (Gen 4) actually happen to fit me perfectly, but I completely understand that there are so many different shapes and sizes of people. One good example for me was my Smith and Wesson Model 66. When I would attempt to get a high grip, the finger grooves would jam right into my knuckle, causing much discomfort, and forcing me to get a less that optimal hold on the gun. That is why it’s quite interesting that Lone Wolf decided to leave the finger grooves on their Timberwolf frame. But, to their credit, they reduced them down quite a bit, so if they don’t fit you well, it may not be the largest discomfort, when compared to a factory frame. I would still like to have seen them remove the grooves, though.

Moving up the grip, we have the undercut trigger guard. This is another common modification that allows you to get a much higher purchase on the pistol. To help with that, even further, they also designed the rear grip higher, and added a beaver tail, to remove the risk of slide bite. I have never personally had the web of my hand bitten by a Glock slide, but I have fairly small hands, and can see where it would be a problem to larger-handed shooters.

One last minor change I would like to see in the grip would be a slimmed down portion where the trigger finger rests on the frame, similar to that of the Walther P99. I feel like it would allow shooters with shorter fingers to more properly grip the handgun, and reach the trigger.

Magazine Release

For the longest time, people have been adding extended mag releases to guns, to make them easier to actuate. Lone Wolf, as well many other aftermarket parts manufacturers, offers extended releases. Lone Wolf even offers one that is wider than the factory, but it requires custom machining to make it work. When designing their frame, they decided to incorporate it right in, that way you don’t have to have it modified later. The wider release offers people with shorter fingers, like me, an easier to reach release without shifting the grip, as well as an easier to find release, which is good for everyone. As with the front strap, the corner of the magazine release can be a little sharp and annoying, if you’re performing repeated actuations, but, like I said previously, it’s not something a little swipe of sandpaper wouldn’t take care of.

20151024_180545

Another curious note on the mag release is that Lone Wolf didn’t make it reversible, like the Gen 4 Glock. That would be a nice feature, but seeing as how it was designed before the Gen 4 was released, I can understand the oversight.

Rail

20151024_180227

The final feature of the Timberwolf frame is the rail. Rather than using Glock’s proprietary rail, Lone Wolf decided to go with a Mil-Standard, three-slot, Picatinny rail. This allows users to select from a wider array of rail-mounted accessories, as well as move the placement forward or rearward, as they see fit. I did not attach anything to the rail, though.

 

Overall

The Timberwolf frame is very a very well thought out replacement for anyone that owns a Generation 3 or older Glock handgun in 9 Luger, 40 S&W, 357 Sig, and even 45 GAP. It is available in either the full-size (17, 22, 31, 37) or the compact (19, 23, 32, 38) frame sizes. The improvements offered by a good grip modification company could run well into the $4-500+ dollar range, whereas Lone Wolf offers many of these features at a fraction of the cost. If replacing a Gen 3 frame for a gun you already own, you could buy just the bare frame and use most of your existing Glock parts to fill the replacement. That is, with the exception of the mag release, since the Timberwolf frame comes with their proprietary release pre-installed. The bare frame will cost you just shy of $200, which is a steal, compared to grip work. If you do build your own frame, you should be aware that you will need to buy either a LWD Gen4/Timberwolf Trigger housing, or LWD Ultimate Trigger Stop Gen4, to replace your Gen 3 housing, as the grip is slimmer in the front-to-back dimension.

If you’re planning to build a whole new gun, or just want multiple lowers, Lone Wolf offers a pre-assembled lower frame for $330, which is only about $30 more than buying every individual part and installing them yourself. To save the hassle and time of potentially forgetting or losing a part, I would recommend just buying the built frame. But, if you want to add your choice of custom trigger, you could easily purchase the parts separately from the frame. Lone wolf makes this easy by offering an interactive schematic.

Another benefit of buying the assembled frame is that Lone Wolf adds a few enhanced parts. These enhancements include: LWD 3.5# connector, LWD 6# trigger spring, LWD Extended slide stop, and LWD Extended slide lock. The 3.5# connector and 6# trigger spring makes for a very smooth, and pretty light, trigger pull. This is a great upgrade over the factory Glock parts that I am glad Lone Wolf includes in the assembled frame. It provides a good trigger feel, without being obscenely light, so I feel it would still be suitable for carry. On my example, they even installed the smooth trigger that usually only comes with the full-size Glock handguns. I much prefer the smooth trigger, as the serrated trigger begins to wear at my trigger finger, during firing sessions. I’m not sure if this is the standard feature for the assembled frame, but based on my invoice, it seems to be. The Extended slide stop is useful if you are the kind of shooter that uses it to release the slide. It provides a much larger purchase area than the standard, so it’s easier to manipulate, but it’s not so large that it gets inadvertently hit. As far as the Extended slide lock (the two tabs in front of the trigger guard that you pull downward to disassemble the gun), I really don’t get the purpose of it. The tabs are a little longer than standard, but I’ve never had a problem using the standard Glock part. It’s an upgrade that I could take it or leave it, and be satisfied either way. It did, though, scratch the inside of my holster. That’s not too much of an issue with a plastic holster, but with leather, I’d be afraid of it causing premature wear on the holster.

In summary, the Lone Wolf Distributers Compact Timberwolf Frame is a great upgrade to your Gen 3 or older Glock pistol, or for building your own custom pistol. It is a great value compared to the expense and wait for frame modification work. Some of the features are addressed on the newer Gen 4 Glocks, but with the Timberwolf, the grip is still slimmer (front-to-back) than the OEM. You also wouldn't get the undercut triggerguard, raised and lengthened beavertail, and reduced finger grooves.

At the time of writing, the assembled frame is available for only $234.95 (prices subject to change), and it even comes with Lone Wolf's excellent Ultimate Adjustable Trigger. This is a promotional price for the UAT, and I do not know the timeline for when it will go back to normal, so if you'd like an assembled Timberwolf frame, I would jump on it as soon as possible. The UAT is normally a $50 upgrade, so you are basically paying for the frame and the assembly labor cost, and getting all of the internals for free!

Firearms Insider Reviews - 8 Key Points

Claim to Fame: Replacement frame for generation 3 and older Glock handguns

Target Market: Concealed carriers and competitive shooters

timber

FNBs (Features & Benefits of this product):

  • Improved ergonomics over Glock OEM frame
  • Full-spec 1913 accessory rail
  • Higher grip angle
  • Extended beaver tail
  • Rounded trigger guard
  • Round/extended mag release
  • Improved Checkering
  • Quick change grip panels (2 total)
  • Spare CR2016 battery storage in grip panel
  • Improved trigger over Glock OEM (standard in assembled frame)
  • Extended slide lock lever (standard in assembled frame)

What other aesthetic options or finishes are available?: Currently, the Timberwolf frame is only available in black.

What others are saying?:

“The Timberwolf pistol is of particular interest to the small-handed shooter, or to the user who says “I love everything about the Glock but the grip angle,” or the handgunner who just likes to be able to get lots of finger on the trigger and lots of flesh and bone around the “handle.” It’s definitely worth a look.” - Massad Ayoob, Daily Caller

“But the Not-A-GLOCK feels terrific in the hand. No really. Like many, but not all shooters, I find it difficult to come to a natural point of aim with a standard GLOCK. What’s more, the grip angle puts my hand and wrist out of the line that gives me stability. The Compact Timberwolf’s grip is, for me, vastly improved. I can get a high hold on the gun and put all of my fingers on the handle. It boasts a fairly small diameter grip, with good holding surface. I can get a natural point-of-aim and a solid one-hand grip, right or left.” - Jon Wayne Taylor, The Truth About Guns

Price Point:

  • Bare = $199.95
  • Built = $329.95
  • Built with UAT = 234.95 (Limited time offer)

I need it now! Availability: You can get the Timberwolf Compact Frame directly from Lone Wolf, and a few online retailers, but once you spend a few minutes on the LWD website, you’ll most definitely want to pick up some of their other great products, like their Glock Magazine Disassembly tool.

Our Rating:

Pros:

  • Greatly improves ergonomics
  • Interchangeable grip panels
  • Offers many common custom options
  • Improved grip texture to provide better traction
  • Available as a bare frame or built to LWD’s preferred specs
  • Built frame has improved trigger
  • The ability to build any caliber offered by Glock on this frame size (19, 23, 32, & 38)
  • You can even build it as a “Long-Slide Compact” by using a factory full-size upper (such as a G17), or Lone Wolf upper, and purchasing Lone Wolf’s Slide Adapter, which fills the gap between the front of the 17 slide and the 19’s dust cover.

Cons:

  • Still has finger grooves (though they are greatly reduced)
  • Mag release is not reversible to left-hand operation

Score: 9.090

 

 

Visit the Firearms Insider Facebook page for alerts on new reviews, and updates on the show.

Firing Line Review

 

 

SEARCH