Chad Wallace

Foxtrot Mike - Mike15 gen 2

200 rounds of ammunition was supplied by Target Barn for the review

  AR pistols have become very commonplace. Foxtrot Mike has designed their pistols and rifles to be a little different, but in a good way. They use an integrated bufferless recoil system in their Gen II AR’s. Foxtrot Mike sent me a 12.5 inch Mike-15 pistol with a few added in options. So let’s get into what advantages this Mike-15 has to offer.

  When you first look at the Mike-15 Gen II, it looks very AR15ish. That is because most of it is. The lower receiver is Foxtrot Mike’s standard AR15 billet lower. But installed in the lower is a rear picatinny mount that also doubles as the bolt stop. The upper receiver system is where the difference is. Yes, it uses a standard AR barrel assembly and is still direct impingement. Because the Mike-15 is a bufferless system, the bolt carrier is different. As is the self contained recoil system that is placed above the bolt carrier, not behind like in a standard AR. This does make the upper about a quarter inch taller than your standard AR. The Mike-15 also uses a forward charging handle. All of these work very well together.

  As mentioned, the Foxtrot Mike, Mike-15 lower receiver is billet. This means that it is machined from a solid block of aluminum, not from a forging. This allows Foxtrot Mike to add in some different features. One of those is an oversized built-in trigger guard. This guard also has a slot in the bottom of it. I don’t know if it is for weight savings, or if it is for something else, but it looks nice. Foxtrot Mike also machines in a radiused 3 dimensional magazine well. This is a pretty nice feature to aid in reloading the rifle/pistol, even if you can see a few light machine marks in the magwell. Some other advanced features are: a screw in bolt catch pin, threaded and set screwed spring for the rear takedown pin, a ball detent for the safety with a set screw to hold it in (normal style spring and detent work also), and a screw for tightening the upper to lower fit. This Mike-15 also came with an upgraded Hiperfire trigger and an ambidextrous safety selector. The safety selector came as a 90 degree throw, but can be switched to a 45 degree, which I did as I like short throw safety levers. The optional Hiperfire Eclipse trigger is fantastic and has a pull weight of 2.5 pounds. The Hiperfire is not listed as an option on the website, but contact them and they will let you know how much extra it adds to the price. I also have a stripped Mike-15 lower for a different project, this is partly why I know about all those extras. I should also mention that the rear picatinny rail installs into the buffer tube threads and has the recoil bumper attached in it. It also has a QD slot at the bottom of the rail, so if a brace is not attached, a sling can be.

  The Upper receiver of the Foxtrot Mike is really where the huge differences are in this pistol, and their rifles. To start with, the upper receiver contains the recoil system. It is housed above the bolt. This recoil system consists of a dual spring and guide rod. The guide rod also goes through the top part of the bolt carrier. This allows the bolt carrier to push against the recoil system. The Mike-15 then uses a standard AR bolt assembly, but not a standard carrier. Because of this system, the receiver is about a ¼ inch taller than a normal AR’s receiver. The extra ¼ inch can make optics sit a little higher. This doesn’t cause any problems on the pistol version, but on a rifle, your optic may need a slightly lower mount. Foxtrot’s upper receiver does not have a forward assist, but does have a shell deflector. The Mike-15 gen II still uses a gas impingement system, so no differences over a standard AR in that respect. Except that the gas block is pinned, not set screwed or clamped. Foxtrot Mike then installs a 4150 barrel. This one is 12.5 inches with a mid length gas system. Because of the higher receiver height, a M-Lok rail that matches the height of the upper is installed. This handguard measures 11.75 inches, so it comes up flush with the muzzle brake. Depending on the rifle or pistol you order, the handguard length will vary. Lastly, Foxtrot Mike put a nice little 4 port compensator on this pistol. The comp works better than I was expecting it to.

  Operation of the Mike-15 gen II is a little different then a standard AR15. Instead of using a rear charging handle, Foxtrot Mike designed a forward charging handle that is in the upper part of the handguard. The charging handle is basically in the part of the handguard that is taller, so it doesn’t affect the M-Lok slots or get in the way. You can set this charging handle up to be either right or left charging. The charging handle DOES NOT reciprocate. However, it can be angled either slightly up, or slightly down, depending on how you have it configured. It comes curved up on the left side of the firearm. A folding lever is also available from Foxtrot Mike. The folding lever folds out of the way against the upper, for a more streamlined charging handle.

  Maintenance on the Mike-15 gen II is also a little different. Because of the self contained recoil system, you can not just pull the bolt out like a standard AR. On the top rear of the upper, there is a little square plug with a hole in it, located where the charging handle on a regular AR would be. One must use a small punch, or something, and push down the recoil spring assembly. Then slide the plug down. Watch out for lift off of that spring, as it can go flying. Then just pull the recoil spring assembly out, tip the gun back, and the bolt carrier should slide right out. All the other maintenance stuff is pretty similar to what a standard AR is.

  The Mike-15 pistols come in a variety of options. Some of those are barrel length and different colors. These pistols can be had in the picatinny rail version. Meaning they only have the pic rail on the rear of the receiver. Or you can get them with a folding SBA3 brace. I'd opt for the folder. The Mike-15 12.5 inch they sent me had an A3 Tactical folding brace with an A3 Steady Brace. These braces are top tier and work great. Plus they are super lightweight. If you want one of these as an add-on to your Mike-15, just ask Foxtrot Mike Products to see what they can do for you. The A3 brace folds to the left side of the Mike-15. Because the Mike-15 uses the forward charging handle, the brace does not get in the way of manipulating the firearm. Yes, of course the Mike-15 will fire while the brace is folded because of the self contained recoil system. 

  The Mike-15 that they sent was pretty solid. I’ve run a bunch of bill drills with it, along with other stuff. Target Barn supplied some 5.56 to help with the review: 100rds of Winchester 5.56 55gr M193 and 100rds of PMC 5.56 55gr. The Mike-15 currently has over 500 rounds through it. I did run into a problem with the recoil system after around 150 rounds. The springs were binding up and wouldn’t allow the bolt to go rearward all the way. I contacted Foxtrot Mike and they sent the “new” style buffer springs and guide rod. I literally had them the next day! Somehow the “old” style guide rod had been installed in this Mike-15. It has run flat out since with zero malfunctions since the initial problem. During my conversation with Foxtrot Mike, they also told me that they have a buffer tube spacer that plugs the buffer tube in case you want to run the Gen II uppers on a standard AR. They sent me one, so I tried it. The Gen II Mike-15 upper ran fine on a standard AR lower with that buffer tube spacer. One thing to mention is that the Mike-15 uses a different manual of arms, kind of. Because of the forward charging handle, one needs to readjust a little. Is this a bad thing? I don’t think so, but I thought it needed mentioning. When it comes to that manual of arms, the Mike-15 also seems to take a little more muscle power to manually cycle the bolt. Probably a non-issue for most. Watch a short clip of how it runs HERE.

  There are a few aspects of the Mike-15 that I really like. The first is the folding brace. I really liked this addition. One, because it folds and makes the Mike-15 really compact. Two, because it has M-lok slots in the arm. Having M-lok allows me to install a QD socket so I can run a sling easily. The next aspect I like is the weight. It weighs 5.6 pounds on my scale, and that is with the Lucid E7 blue-dot optic and the brace. When it comes to performance, the Mike-15 can hold its own. Being only a 12.5 inch barrel, I do shoot it slightly slower than a 16 inch barreled AR, but it is still fast. The Hiperfire trigger helps with the speed also. It is a very nice trigger upgrade. Lastly, I really like the self contained buffer system as it makes the Mike-15 pistol something you can shoot with the brace folded. I’d say the performance of the Mike-15 is above par for the price you pay.

  Foxtrot Mike designs their products for the everyday user. You get a high quality product for not a ton of cash. The Mike-15 Gen II pistols start at $699 MSRP and work their way up from there, depending on options of course. If you are looking for a truly foldable ARish pistol or rifle, the quality you get from Foxtrot Mike is top notch. You can check them out over at fm-products.com.

Firearms Insider Reviews - Key Points

Claim to Fame:

Bufferless AR style rifle or pistol

Target Market:

Those wanting a non conventional AR that has the advantage of not having a buffer tube.

Features, Benefits, and Specifications of this product:

  • CALIBER: .223 WYLDE

  • OPERATING SYSTEM: DIRECT IMPINGEMENT

  • BARREL LENGTH: 12.5"

  • BARREL TWIST: 1:8

  • BARREL MATERIAL: 41V50 PREMIUM MATCH GRADE 41v50 BARREL, VACUUM STRESS RELIEVED, MELONITE COATED WITH A BURNISHED CHAMBER

  • GAS SYSTEM: MIDLENGTH

  • GAS BLOCK: 0.625" NON-ADJUSTABLE

  • UPPER RECEIVER: BILLET AIRCRAFT ALUMINUM TYPE III HARD BLACK ANODIZING 

  • LOWER RECEIVER:  BILLET AIRCRAFT ALUMINUM TYPE III HARD BLACK ANODIZING 

  • HANDGUARD: 11.75" M-LOK FREE FLOAT TYPE III HARD BLACK ANODIZING

  • CHARGING HANDLE: 4 POSITION NON-RECIPROCATING FRONT CHARGING HANDLE

  • PISTOL GRIP: THRIL

  • BUFFER LESS  

  • LENGTH (INCHES): 22"

  • WEIGHT (LBS): 4.7 without brace or optic

What other aesthetic options or finishes are available?

Various lengths, rifle options, etc.

What others are saying?:

5 out 5 stars at Brownells - yes it’s for the rifle version, but it is still close   

One of my favorites

I purchased the 16" as well as the 11.5" pistol version. I shot the 16" primarily and was able to zero at 100y and hit targets at 500y without issue. A bit more fine tuning with my scope could yield a bit more in its capability. Some things to note about the rifle: I had some issues with the first round in a magazine going into battery and having light primer strikes that were rectified through break-in. After a couple magazines, I had zero errors. The biggest issue I had was getting proper eye level with my sight. Be aware the Zhukov stock and the folding, mounting system sits 0.25" lower than a standard AR. You may have to buy the $15 0.25 Magpul AK Riser to get the proper eye line. I paired my 30mm LVPO with a low mount, cantilever scope mount. In all, it only cost an additional $50, but I wish there were a way to have the stock sit at the same level as a buffer tube would. This is information I wish had been noted in reviews/videos before purchasing the rifle. Am I happy with my FM-15?Yes, it's probably my favorite AR long gun. Would the sight-line information have changed my decision to buy? Maybe, but ultimately I'm happy to own such a unique rifle. Time will tell if I enjoy the pistol length version as much as the 16".Though, I do hope Foxtrot Mike develops a 300BLK, short barreled upper of the same style.

Link to other reviews:

Tiberious Gib on YouTube   

Pew Pew Tactical   

Price point:

MSRP = $699.00 +

As tested = Approximately $1125

Retail = Same

I need it now! Availability:

Foxtrot Mike or Brownells

Our Rating:

Pros:

  • Lightweight

  • Folding brace

  • Self contained recoil system

  • Pinned gas block

  • 3D magwell

Cons:

  • Manual of Arms is slightly different 

  • Harder to charge the firearm when compared to an AR

Score:  8.00 Great

Favorite Link:  Gforce Arms Rapture review

Cobratec Rath

  When it comes to pocket knives, I always try to recommend ones that will not kill the wallet. Cobratec Knives happens to be one of those companies. Yes, they make higher priced items also, but they have plenty in the under $100 range. The Cobratec Rath is one of those. 

  Cobratec’s Rath is a nice everyday folder. It uses a flipper on the top of the handle to open up the knife. And a liner lock to hold the blade in place. Nothing fancy for the Rath as this style of every day carry (EDC) knife has been around for ages. The Rath is a simple knife that works well.

  The specifications on the Rath are what make it shine. It starts with a coated D2 steel blade. If you happen to listen to the podcast, you know that we like D2 steel as a great inexpensive knife blade material. It holds an edge decent enough and is easy to sharpen. I have not needed to sharpen the Rath. Granted, I did not abuse it like the Black Mamba that Cobratec sent for review. The coating on the blade also helps protect it from the elements. A nice touch since D2 is not a stainless steel. The blade's thickness is 0.12 inches and Cobratec hardens it to 55-62 HRC, which is pretty standard for D2.

  Cobratec chose to use G10 for the Rath’s handle. G10 is a composite material that gives the handle good strength. It also is impervious to a bunch of chemicals. The G10 handles will probably outlast the Rath’s blade. Another advantage to G10 is its texture. Even when not texturized, it still has great grip. Exactly what you need and want in a knife handle. The Rath has smooth handles, but they still allowed me to get a good grip on the Rath, partly because of that G10 material.

  The Rath uses a flipper style opening. I like flipper opening knives, and the Rath’s flipper works extremely well. The blade just flips right out. One of my complaints with the Rath is that it only uses a flipper to open it. There is no other way to open it. I’d like to see a little slot or something in the blade so that there is at least another option to open it. However, this does not keep me from liking the smooth operation of the Rath’s flipper. The Rath also uses a liner lock to keep the blade out once it has been opened. The liner lock also performed as expected. To close the knife, just push sideways on the liner to unlock the blade, and then pivot the blade in.

  Now that I have gone over the general stuff, let us get into the numbers. The Rath uses a 3.5 inch long drop point blade. I really like EDC knives in the 3-3.5 inch blade length range. So the Rath checks that box for me. I also am a fan of good drop point blades, and the Rath’s blade shape is very useful. The blade hides in a 4.5 inch long handle that also carries the pocket clip and lanyard hole. I do not use lanyards, but the hole is there if you do. I did like the deep carry pocket clip. It puts the knife pretty far down in your pocket. When the knife is open, it is 8 inches long. Imagine that, a 3.5 inch blade plus a 4.5 inch handle makes 8 inches. For a knife this size, the Rath is fairly lightweight, tipping the scales at 4 ounces. I was really happy with the lightness of the Rath. It is easy to carry in the pocket. 

  I have used the Cobratec Rath for a bit and it has treated me well. The drop point blade cuts nicely for me. It has cut lots of boxes, a few steaks, and some other stuff, all the time doing what a knife should do, cut. One aspect I really liked about the Rath is the jimping on the top of the blade. There is not a lot of it, but it is cut deep enough to get a good non-slip grip with your thumb. The handle’s shape is also very comfortable in my hand and is pretty slim, which I like. I also think the Rath is a good looking knife, especially with the red accent around the pivot.

   Cobratec’s Rath is a good EDC knife. It uses a good coated blade. It has a nice G10 handle. It uses a tried and true flipper opening and liner lock. Plus it looks good. And you get all this for under $60. What more could you ask for in a simple EDC knife? So head over to Cobratec and check out the Rath.

Firearms Insider Reviews - Key Points

Claim to Fame:

Quality Everyday Carry Flipper knife

Target Market:

Every Day Carry or anyone wanting a decent, well priced pocket knife

Features, Benefits, and Specifications of this product:

  • D2 Black Blade

  • G10 Handles

  • 3.5 Inch Drop Point Blade

  • 4.5 Inch Handle

  • 8 Inches Overall

  • Blade Thickness: 0.12”

  • Blade Hardness): 55-62 HRC

  • Liner Lock

  • Weight: 4 Ounces

  • Deep pocket carry clip

  • Flipper

  • Lanyard hole

  • Lifetime Warranty 

What other aesthetic options or finishes are available?

Brown, Grey, OD Green, & Red

What others are saying?:

Nothing found as of publishing

Link to other reviews:

Nothing found as of publishing

Price point:

MSRP = $59.99

Retail = Same but use code “GGR10” FOR 10% OFF

I need it now! Availability:

Cobratec Knives

Our Rating:

Pros:

  • G10 Handles

  • Flipper works nice

  • Price

  • D2 blade

  • Deep pocket clip

Cons:

  • Flipper is only way to open

  • No serrated option

Score: 8.00 Great

Cobratec Large Black Mamba

  Out the Front (OTF) knives have become pretty popular in the last decade. Because of this, I decided to try one out. Cobratec Knives offered me one of their Large Black Mamba’s to review. This is one of their cost effective automatic OTF knives. As it uses D2 for the blade steel. Also, do not let the name fool you, large does not mean huge. The Large Black Mamba is a good size Every Day Carry (EDC) knife.

  As stated, the Cobratec Large Black Mamba is an OTF knife. If you are new to knives, that means the blade actually extends out the front of the knife, through a slot in the end of the handle, automatically. It does this by either a button or switch located somewhere on the handle. The Black Mamba uses a slider switch on the top edge of the handle. It is a dual action switch. Slide it forward to extend the knife’s blade out, and rearward to retract the blade. I do like the switch on the Black Mamba. It has some serrations on it to let your thumb get a good grip on it. The switch is also ramped up and down to position your thumb at the perfect location to use said switch. 

  The specifications of the Black Mamba are what make it a good OTF knife. Even though Cobratec calls it the “Large” Black Mamba, it’s only called large because it is the biggest in the Mamba line. The blade’s length is 3.25 inches long. Making it the same size as a ton of folding EDC knives on the market. Moving to the handle, it has a length of 4.75 inches. This makes sense to me, since the handle houses the mechanism to open the knife, as well as the blade itself. That makes the total length, opened, to be 8.25 inches. The handle's thickness comes in at 0.49 inches and 0.60 with the pocket clip. The height of the handle measures 0.925 inches wide or 1.09 inches if you include the slider switch. I thought the Black Mamba would be larger, but once I received it, I realized it’s basically the same size as most of my EDC knives.

  Cobratec uses D2 steel for the Large Black Mamba’s blade. I like D2 as I believe it is one of the best lesser expensive steels used in knife blades. This also helps keep the cost of this OTF knife down. D2 is not a stainless steel, so to help keep it from the elements, Cobratec gave it a black titanium coating. The coating does two things: It helps protect the blade and it gives it a really nice look. The blade on the Black Mamba is a drop point shape. It is also not serrated. I’m okay with this as I find straight drop point blades very functional. This particular blade is 0.100 inch thick and 0.650 wide. I would have possibly liked a wider blade, but I am not a OTF designer. So there are probably design limitations due to the handle’s width. But the Black Mamba’s blade shape worked well. Being that the Black Mamba is an OTF automatic knife, it does have a blade safety mechanism. If you try to open the knife with something significant blocking the blade from pushing out, the blade will release from the opening mechanism and become loose inside the handle. It will also disengage if you hold the blade tight while trying to retract the blade back into the knife. To get the Black Mamba back into action, just pull the blade all the way out and it will re-engage the opening/closing mechanism. You can also flick the knife and use gravity to do the same thing. This is a common safety feature on OTF knives. 

  I mentioned the handle’s dimensions, but let’s go a little deeper into the handle. The Black Mamba’s handle has little squares machined into it for grip texture. Actually, the lines are machined in it to make the squares. On the top and bottom, Cobratec machined some lines in to give rectangles. All of these squares and rectangles give the Black Mamba a really good grip. Especially since the handle is made from 6061 aluminum, and aluminum can be slick. On the rear of the handle is a built-in glass breaker, should you ever need one. Also on the handle is the pocket clip. It is tip down, right hand only. Tip down is because it is an auto knife. When you grab the knife out of your pocket, your hand is already positioned with the pokey end pointed away from you. So when you push the opener switch, you don’t get hurt. My only real complaint about the Black Mamba is its pocket clip, it is not a deep carry clip. However, the pocket clip works extremely well and is very strong.

  As with almost all of my knife reviews, I like to actually use the knife. I carried the Large Black Mamba for a while. It carries really well. Or at least as good as most of my flipper style knives. The D2 blade came extremely sharp from the factory. I have had to touch it up twice. D2 sharpens pretty easily, so it wasn’t a big deal. One of those times I dulled it up by scraping some stuff off of a metal surface. Probably something that no knife maker recommends. The opening mechanism has also never let me down. Plus it is super easy and fast to use. I’m not a big OTF guy, but the Black Mamba performed great for everything I threw its way. 

  If you like OTF knives, or maybe want to get into OTF knives, the Large Black Mamba might be just what you are looking for. It is priced right at $170. Has a good blade steel. It functions fantastic and has a good blade shape. What more could you want from an OTF knife? Go check out the Cobratec Large Black Mamba and see for yourself. Or at least take a look into all the other OTF knives Cobratec makes. 

Firearms Insider Reviews - Key Points

Claim to Fame:

Everyday Carry Out the Front knife

Target Market:

Anyone wanting a quality OTF knife

Features, Benefits, and Specifications of this product:

  • Weight: 3.5 oz

  • Blade Length: 3.25"

  • Handle Length: 4.75"

  • Total Length: 8.25"

  • Titanium coated Drop point D2 blade

  • 6061-T6 aluminum handle - textured

  • Side opening slider switch

  • Glass breaker

  • Lifetime Warranty 

What other aesthetic options or finishes are available?

None

What others are saying?:

Nothing found as of publishing

Link to other reviews:

Nothing found as of publishing

Price point:

MSRP = $169.99

Retail = Same but use code “GGR10” FOR 10% OFF

I need it now! Availability:

Cobratec Knives

Our Rating: 

Pros:

  • Lightweight

  • Price

  • Good grip texture

  • Good blade design

  • Glass breaker

  • Fast

Cons:

  • Pocket clip isn’t deep carry

  • Blade is a little narrow

Score: 8.00 Great

Favorite Link:  Gideon Optics Judge review

Hi-Point 3095

  Hi-Point Firearms has made it a point to make inexpensive firearms. They also are not the junk people on the internet say they are. In fact, they make one of the only carbines in 30 Super Carry, the model 3095. The Hi-Point 3095 carbine they sent me for review was quite reliable and fun to shoot. 

  The 3095 carbine has a lot of decent mechanical features. It uses a blowback style action to keep the gun's operation simple. Because of this, there are not very many parts that can go bad. Basically, you have a barrel, the slide, recoil spring, and a trigger assembly. The barrel is fixed into the action, which can give some really good accuracy. In fact, I was pleasantly surprised by how accurate the 3095 was. 

  Sighting features of the Hi-Point carbine are as expected. There is a hooded post front sight with a ghost ring style rear sight. This sight worked really well, even if it is a little slower to pick up than say an AR15’s iron sight. The rear sight is easily adjusted for windage and elevation, with little hash marks to know where it’s at. One can use a small screwdriver to adjust it. Now, I did have the front sight post come loose after about 250 rounds. It was easily repaired by tightening the two screws back up. I used loctite, maybe Hi-Point forgot to do that. The rear sight is removable by unscrewing a couple of screws. Once removed, it gives access to the top picatinny rail. The rail is plastic, but that doesn’t seem to affect it. Hi-Point also put a short piece of pic-rail under the front handguard and under the barrel. That way you can attach accessories. Or you can remove it if you don’t want it on. 

  Operation of the Hi-Point 3095 is straightforward. To cycle, or charge, the carbine, just pull back on the charging handle. It's on the left side of the firearm and does reciprocate when firing. One also has to install the handle when the carbine comes out of the box new. Just screw it in and tighten with the supplied multi tool. I would recommend blue loctite because I did have the handle come loose without it. On the left side of the pistol grip is the magazine release. The magazine goes into the pistol grip like a handgun typically would. Right above the pistol grip, on the left side only, is the safety. Move it up for safe and down for fire. No, the controls on the 3095 are not ambidextrous. They also are not placed where it is easy for me to get to them. I have to take my hand a bit off of the pistol grip to move the safety into the “fire” position. But not to put the safety on. I also have to twist my hand slightly to depress the magazine release. If you have larger hands, this may not even be a problem for you. Moving to the trigger, it is not great. Yes, it has a smooth pull, but it is long and takes a 7lb pull to get it to fire. The carbine will lock the bolt back on the last round fired. But there is no way to lock the bolt rearward without an empty magazine in the firearm. 

  As mentioned, the 3095 carbine comes with a multi-use wrench. The wrench has everything you need to adjust and take apart the carbine. Also included with the carbine are a sling. The sling is just a two point style used for carrying. It is not a quick style sling. Probably the most important tool in these add-ins is the magazine loader. It helps quite a bit getting those little 30 Super Carry rounds into the single stack magazines. Unfortunately these magazines only hold 10 rounds each. Good for magazine restricted states, not so good for the rest of us. 

  Ergonomics of the Hi-Point 3095 are actually pretty decent. The stock and handguard are polymer, as is the pistol grip, which is also part of the stock. The forend gives good grip with its molded grooves. The pistol grip feels good, even if I can’t get to the safety easily. Then there's the stock. It is really nice. Part of this is due to a decent cheek rest. But the other part is because of the spring assisted butt plate. This helps soak up recoil. Okay, what little recoil the carbine has. My only complaint about the stock is that the length of pull is fairly long. This makes it harder to use for small statured people.

  The 3095 carbine is fairly short. It is 31” overall. To put that in perspective, my 11.5” AR15 is the same length with the stock fully extended. Yes, my AR is a registered SBR. So the Hi-Point carbine gives you short barrelled rifle (SBR) length without the hassle of registering a SBR. Plus with the 3095, you get a full 16.5” barrel length. Another plus, the Hi-Points barrel is threaded ½-28 so you can add something like a 9mm suppressor. This 3095 carbine also only weighs in at 6 ¼ pounds. The Hi-Point 3095 gives you a nice size package in a pistol caliber carbine.

  Hi-Point makes their carbines in a bunch of calibers. I chose this particular one because it is in the newer 30 Super Carry cartridge. The 30 Super Carry is a 30 caliber “pistol” cartridge. It was designed to bridge the gap between 380 and 9mm. Yes, the bullet is smaller but it is in the same weight range as lighter 9mm loads. Most of my testing was done with CCI Blazer 115 grain 30 Super Carry rounds. In a carbine like the 3095, the 30 Super Carry benefits from some added velocity, making it a good choice for home defense. In a pistol, it also increases the amount of ammunition you can put into a magazine. Assuming the pistol is the same size and model. It is too bad that the Hi-Point carbine doesn’t benefit from the higher possible magazine capacity. Either way, the 30 Super Carry round really impressed me out of the 3095 carbine.

  One might ask what is a good use for a Hi-Point carbine? There are many. You could use it as a home defense weapon. This is because it is light and maneuverable. Plus they are far more reliable than the internet makes them out to be. Another use might be a “truck” gun. Something that can reach out farther than a pistol but has little recoil. And last, just something to have fun with at the range or out plinking in the woods. The Hi-Point 3095 can fit a variety of shooting needs.

   How do I feel about the Hi-Point 3095 carbine? First off, I love how well it shoots. There is very little recoil in the 30 super carry round. It is fairly accurate. I was getting 1”, 10 shot groups at 25 yards, off hand, with the factory sights. The carbine is short, which makes it handy to use. I personally didn't care for the ergonomics of the grip and safety. However, I did like that the barrel is threaded. In fact, I even put my sub-gun suppressor on it to try it out and it worked fine. The little 30 Super Carry round is quite potent and is moving pretty fast. Which is a good combo for this carbine. I liked the 3095 carbine way more than expected.

  Sometimes you come across something that surprises you. The Hi-Point 3095, in 30 Super Carry, may just be that for you, it was for me. It made me really like the round it fires. It functioned fine throughout the review. Maybe I had to tighten some set screws, but that's not something that stops the gun from functioning, just being able to hit something. Is it the best? No, but it was reliable for me and a whole lot of fun to shoot. If you want a firearm that will not break the bank, but still functions, and in a caliber that does not have much recoil, the Hi-Point in 30 super carry may be the trick. You can check it out over at Hi-Point.

Firearms Insider Reviews - Key Points

Claim to Fame:

Inexpensive 30 Super Carry Carbine

Target Market:

Home Defense, Range Use, Just a fun carbine

Features, Benefits, and Specifications of this product:

  • Weight: 6.25 lbs.

  • Capacity: 10-shot magazine standard

  • Overall length: 31"

  • Sights: Fully-adjustable

  • Stock: All-weather black molded polymer

  • Threaded 1/2 x 28 barrel w thread protector 

  • Thumb magazine release

  • 100% American-made parts and assembly

  • Internal recoil buffer in stock

  • Last round lock open

  • Picatinny rails

  • Manual thumb safety

What other aesthetic options or finishes are available?

.380, 9mm, 40 S&W, 10mm, & 45 ACP

What others are saying?:

Nothing to note as of publishing 

Link to other reviews:

GUNS.com Review   

Price point:

MSRP = $369.00

Retail =  $309.99   at Guns.com

I need it now! Availability:

Guns.com or your local Hi-Point dealer

Our Rating:

Pros:

  • Price

  • Only 30 super carry carbine on the market

  • Accurate 

  • Compact size

  • Recoil reducing stock

  • Comes with sling

  • Made in the USA

Cons:

  • Quality control - front sight base came loose

  • Single stack only, so low capacity

  • Hard to reach safety

  • Trigger pull

Score: 6.50 Okay

Favorite Link:  Tony’s Hi-Point 995 review

Rogue Apparatus Holster

  When it comes to everyday holsters, most people tend to go straight to kydex. Well, Rogue Apparatus is here to change that with their hand crafted leather holsters. These leather holsters rival kydex in form and function. Rogue Apparatus sent an Appendix Inside the Waistband (AIWB) holster for me to try out.

  The first thing you notice about this holster is how nice the leather work is. Yes, it is handcrafted, which adds to the appeal. They are also molded to your particular firearm. This particular one is for a G19 and is green and black dyed leather. My understanding is that Rogue Apparatus can dye these in just about any color you want. The holster is sewn nicely too. It really is a beautiful holster.

  Moving on to the holster design. As mentioned, this Rogue Apparatus holster is mainly an AIWB. I ended up taking the wing off and using it as just an IWB and it works great in that role. Because the Rogue Apparatus holster is an AIWB, it does not have any adjustments for cant or ride height. The holster uses thick quality leather as the main material. It is then partially wrapped in a thinner leather. This thinner leather also holds the screws for the DCC monoblock so you can clip it onto your belt. DCC clips are my favorite and are the best belt clips I have used. One huge advantage to the Rogue Apparatus holster is the leather treatment. They seal it with an acrylic resolene. By sealing the leather holster in this manner, you get qualities that are similar to kydex. One of these is the ability of this leather holster to retain its shape better over time. The other is how the pistol “clicks” into the holster. It’s not as pronounced as kydex, but the Rogue Apparatus holster has a similar feel.

  I have carried the Lone Wolf Dusk 19 in this holster for some time. I really like the feel of leather. It seems more comfortable next to the skin. Yes, being that the Rogue Apparatus holster has been sealed, it is still stiffer than the leather holsters of the past. The Dusk 19 slides in and out of the holster nicely with some resistance. Since the holster is hand molded, it has indents around the trigger guard, very similar to any kydex holster. This helps aid in retention. The rest of the retention is also decent. This holster is also cut to accept a pistol with a red dot sight on it. One complaint is that the sight channel could be taller to accept “suppressor height” tall sights. Especially since it’s cut away for those red dots. The Rogue Apparatus holster has a nice sweat guard that rides up the side next to your body. This particular sweat guard is not too large or too small, it’s a very useful size. The holster is well designed and lets me get a good grip on the pistol and allows for a clean draw stroke.  

  If you are looking for something different in a holster, maybe more of a piece of functional art, look into a Rogue Apparatus holster. These things function as expected, they are a holster after all. Beautiful is probably an understatement on how they look. You will be  getting a custom leather holster that should treat you well for years to come. I’m pretty happy with what Rogue Apparatus has done with their AIWB leather holster. 

Firearms Insider Reviews - Key Points

Claim to Fame:

Custom Leather holster that functions like kydex

Target Market:

Concealed Carry

Features, Benefits, and Specifications of this product:

  • Made of veg-tan leather that has been custom dyed, formed and sealed with acrylic resolene to retain firm structure and snappy retention

  • Discreet carry monoblock

  • Modwing - removable

  • Stitched with heavy 277 Leather Machine Co threads.

What other aesthetic options or finishes are available?

Pretty much any color combination and clip styles

What others are saying?:

Angelo O. - 5 out 5 stars at ETSY.com     

I ordered this for my Kimber ultra carry ll. It’s a perfect fit, and very high-quality, it has good retention. It’s comfortable and it stays in place with the belt that I use.

Link to other reviews:

Nothing found as of publishing

Price point:

MSRP = $165.00

Retail = Same

I need it now! Availability:

Rogue Apparatus or their ETSY store

Our Rating:

Pros:

  • Looks

  • Good retention

  • Multiple color options

  • DCC clip

  • Leather feels better than kydex

Cons:

  • Sight channel a little short

  • Price

  • No cant adjustable option when compared to kydex

Score: 8.00 Great

Favorite Link:  Vosteed Thunderbird Review

Powertac WOFT

  When it comes to handheld flashlights, there’s a ton of them around. The ultimate question is how do you know which one is right for you? I would go check out reviews and specifications. Which is probably why you are here. Powertac has been doing some pretty interesting things with handheld lights. I’ve reviewed a few of their lights in the past and they performed well. They sent out one of their new lights, the Powertac WOFT tactical EDC light. This light is a collaboration with WOFT (Where Our Families Train) training.

  The Powertac WOFT light is very compact. It has a length of 4.28 inches. A head diameter of 1 inch and a body diameter of 0.85 inches. This makes it fit in the pocket nicely. I usually just throw the WOFT light in my pocket. But for those wondering, it does have a pocket clip. The pocket clip is dual purpose, so it can be clipped onto stuff in either direction. So basically, button up, or button down, whatever suits your carry style. I did find it useful, if you needed to use the Powertac WOFT light as a headlamp. Just clip it to your hat brim and light up wherever your head is facing. The clip can be located around the flashlight body in 4 different locations. The Powertac WOFT is compact enough to make it easy to carry everyday.

  Function of the Powertac WOFT is pretty self explanatory. For instance, the button on the rear tailcap turns the light on and off. One press on, one press off. To momentarily turn the light on, just lightly push the button down. If you double tap the rear switch, you turn on the strobe mode. This works both in momentary and click options, depending on if you want the strobe to stay on or just use it for a wee bit. The tailcap button also has two ears sticking up to protect the button.These ears allow you to stand the light upright on a flat surface. I’m a big fan of a light that can stand up and be used to illuminate a whole room, similar to a lantern.

Front Target stands are 50 yds, Rear are 100 yds. Anything within 50 yds is easily identified

  The Powertac WOFT also has 5 brightness settings. These are: Firefly, Low, Medium, High, and Turbo. The Light ALWAYS turns on in the Turbo made. This is great for a tactical flashlight application, because if you need it, you want it on the highest setting. After the initial turn on, you can cycle through the lights settings by using the side button, which is located on the side of the flashlight's head. Since the WOFT light turns on in the Turbo mode, the first press of the side button takes you to the Firefly mode. Then each consecutive press takes you to the next level. I’m a big fan of tactical EDC lights that always turn on at the highest setting. Powertac hit this option spot on. I also really like the Firefly setting as a task light in dark settings.

  Now what everyone is waiting for, how bright is this Powertac light? It’s plenty bright at 1200 lumens for the Turbo mode. The Turbo mode also spews out a candela rating of 14,400. This gives a good combination of spot and flood. It’s plenty enough to disorient an aggressor. Powertac specs it out at a 240 meter beam distance, we all know that about half of that is useful distance. But that’s plenty for a small handheld light. The light runs off of a rechargeable 14500 cell. Extra are easily found on Amazon and other places. Powertac includes a magnetic usb charging cord that works great for onboard charging of the battery and light. For all you geeks out there (me included), here’s a list of those brightness modes and run times:

Lumens and Run Times:

Firefly - 0.41 lm for 3.4 days

Low - 19 lm for 9.69 hrs

Medium - 140 lm for 3.68 hrs

High - 600 lm for 47 mins

Turbo - 1,200 lm for 43 mins

Strobe - 1,200 lm for 1.18 hrs

  In the box are a few other items. The Powertac WOFT comes with 3 different bezels: a smooth one, a medium aggressive, and a pretty aggressive one. They just screw on, so they are easily swapped. Of course I used the most aggressive one. If I have to use it as an impact weapon, I want it to hurt. But the choice is yours. Also included is a wrist lanyard. I left it in the box, but it’s included if you have a need for it. The included extra bezels are a nice addition.

  The Powertac WOFT has become my EDC light. I carry it daily. Mainly because it has great light output for its size. I like that it’s not too large in diameter. Most other lights in this category seem to have a larger diameter, with a similar length and output. If I had one complaint, it would be run times, but I can’t expect that in such a small light. At first I had a little sticker shock on the price, but after using it for months, I get why it costs what it costs. 

  Powertac and WOFT did a great job putting this EDC light together. From its small size to its impressive output, it does what a pocket edc light should do. Always coming on in the turbo mode is what a tactical light should do, at least if it has more than one output. If you are looking for an edc pocket light, I’d recommend checking out the WOFT light at Powertac, as well as the other lights Powertac offers

Firearms Insider Reviews - Key Points

50, 100, 200 yd target stands

Claim to Fame:

Bright, small, rechargeable handheld light

Target Market:

Anyone needing a small, bright, handheld light

Features, Benefits, and Specifications of this product:

  • 1200 lumens max output

  • 14400 Candela max

  • 6 different settings that include 5 levels of brightness plus a strobe

  • 14500 Rechargeable Battery

  • Interchangeable smoothed, scalloped, & aggressive bezel

  • Magnetic USB Charging

  • Length: 4.28” (108.6mm)

  • Bezel Diameter: 1” (25.4mm)

  • Body Diameter: 0.85” (21.5mm)

  • Weight: 2.61oz (74g) without battery

  • Deep-carry bidirectional pocket clip

  • Reverse polarity protection protects from improper battery installation

  • O-ring sealed

  • Machined from aircraft grade aluminum with type III anodized finish

  • Tempered glass to resist breaking and scratching upon impact

  • Double coated glass lens to give maximum OTF (Out The Front) brightness and beam distance

  • IPX8 waterproof Submersible up to 2 meters under water

  • Lifetime Warranty

What other aesthetic options or finishes are available?

None

What others are saying?:

5 out 5 stars at Powertac.com

This flashlight is a BEAST

There are some fantastic features packed into this bad boy. I love how quick and easy it is to switch to strobe for home security or signaling, then back to Turbo. The WOFT lights up my whole street in Turbo mode. Nice build, well done Powertac!

Link to other reviews:

Tactical Tavern on YouTube   

Price point:

MSRP = $129.95

Retail = $110.45 with discount code “GGR”

I need it now! Availability:

Powertac

Our Rating:

Pros:

  • Small size

  • Bright beam

  • Good beam pattern

  • Always turns on at Turbo setting

  • Multi-Directional pocket clip

Cons:

  • Run Time

  • Price

Score:  8.00 Great

Favorite Link:  Powertac M5 G2 Review   

Primary Arms AutoLIve Battery cap

  We have all had that feeling of forgetting to turn off an optic. Then, the next time you go to the range, or worse, the field, and go to turn on the optic, you see no illumination. Advances in optics allow auto on/off capabilities. But maybe you don’t want to have to buy a whole new optic. Primary Arms has you covered. They have introduced their Autolive battery cap! The Autolive battery cap turns your optic into one that has auto on/off capabilities.

  Primary Arms has made optics that turn the reticle on and off automatically for some time. The Autolive battery cap does the same thing for optics that don’t have this feature. Autolive works by sensing when the optic moves, or hasn’t moved. When Autolive senses movement, it will automatically turn the reticle on. It is so quick, that you will never notice that the reticle was off. After the 2-3 minute mark of no movement, the Autolive function will turn off the power to the reticle. Then, when you move it again, the cycle starts over.

  So what is the Primary Arms Autolive battery cap? It is a battery cap that has built in electronics for the Autolive function explained above. Granted, it is larger than the original battery cap that it replaces, but not by much. I’d say it’s only about ½” taller. Or, it only adds ½” in height to where the battery is installed. A pretty small price to pay for Autolive functionality.

  Installation of the Autolive battery cap is simple. Just unscrew your old battery cap. Remove the 2032 battery. Screw in the Autolive battery cap until snug/tight. Now, the Autolive battery cap has a lock ring on it. Screw the locking ring down and tighten with the supplied tightening tool. Install your 2032 battery into the Autolive cap. Then screw on your original battery cap to the top of the Autolive one. Now adjust your reticle brightness to your desired level. You are now ready to save your battery life and have the illumination function automatically turn on when you move the firearm. 

  I ended up trying the Autolive battery cap on two different optics. The first one was a Lucid Optics L7. Primary Arms doesn’t list the L7 as an optic that the Autolive battery cap works on, but it did. As long as the thread pitch is correct, the Autolive cap should work. As expected, the L7 now had instant on and off reticle illumination. I then transferred the Autolive cap over to a Primary Arms SLx with their NOVA reticle, since this is on a gun I use more. The Autolive cap performed great on it also. The main drawback I see with the Autlive battery cap is that it only works on selected models of optics. These optics are, as listed on the Primary Arms website:

Primary Arms SLx 1-8×24 FFP & SFP

Primary Arms SLx 1-10×28 SFP

Primary Arms SLx 1-6×24 SFP Gen III and IV

Primary Arms SLx 1-6×24 FFP

Sig Optics Tango6® MSR 1-6x24mm

Vortex Strike Eagle® 1-6 SFP

Vortex Strike Eagle® 1-8 SFP

  So if you want to upgrade that optic to auto on/off, the Primary Arms Autolive battery cap just might be the thing. It will save you battery life and hopefully you won’t have that dead battery next time you head into the field. It’s a great option for that beside the bed gun, especially since you know the reticle will turn on when you grab it. If this is something you are interested in, head over to Primary Arms and check out the Autolive battery cap. 

Firearms Insider Reviews - Key Points

Claim to Fame:

Turns illuminated optics on with motion

Target Market:

People who forget to turn off their optics or want better battery life

Features, Benefits, and Specifications of this product:

  • Integrated AutoLive motion sensing technology

  • Instantly turns on optic illumination when you pick up your firearm

  • Low profile design

  • Extends battery life

What other aesthetic options or finishes are available?

None

What others are saying?:

5 out 5 stars from Connor M. at Primaryarms.com

PERFECTION

Does exactly as advertised, and the install was a breeze. Set my rifle with the Gen 4 Nova 1-6 on a table, illumination was on, left it for 5 minutes and came back it was off and then with a poke it came back to life again. Just find your favorite brightness setting (i've found 8 works best for both darker rooms and full day light bright) set it and forget. This and the Nova are a hell of a combo to beat for $400.

Link to other reviews:

Tiberious Gib YouTube    

Price point:

MSRP = $49.99

Retail = Same

I need it now! Availability:

Primary Arms

Our Rating:

Pros:

  • Massively increases battery life on optics without this feature

  • Small - adds very little size

  • Works on a variety of LPVO’s

Cons:

  • Price

Score: 7.50 Good

GForce Arms Rapture

  I recently ran across the GForce Arms GF9 Rapture handgun. I was intrigued by this new micro-compact handgun as it has a bunch of Glock parts compatibility. So much so that I contacted GForce Arms about getting one for review. As you can figure out, GForce sent out a Rapture to do a full review on. The Rapture surprised me with all its features, especially that it can be found for around $350.

G43 on top of Rapture for size comparison. Rapture grip frame is about 1/2” longer with no magazines inserted. Picture is not a perfect representation

  The Rapture is a small 9mm handgun aimed at the carry market. For comparison, it is roughly the same size as a Sig P365X. So it technically fits into the “Micro Compact” size description. The Rapture’s grip frame is larger front to rear, so it feels good in the hand, at least mine. The Rapture is still very narrow, coming in at 1.12” total. It runs a 3.25” barrel for a total length of 6.6”. The main difference in the GForce Rapture is that it has a bunch of parts compatibility with the G26. Including working in G26 holsters.

  GForce Arms put a lot of work into designing the Rapture. For the polymer frame, they gave it a great usable sandpaper type texture. This texture is on the front, sides, and rear backstrap. It is also toward the front of the frame where you would rest your trigger finger or thumb. Speaking of the backstrap, the Rapture comes with 4 different ones. A 0° that comes installed on the Rapture, then a 2°, 4°, and a 6°. These options help the pistol to fit any hand size, from small to large. On the rear of the Rapture is a beavertail to help lessen the chance of slide bite. GForce Arms kept it on the smaller side, I believe, to keep the pistol compact. It still functions as expected. The grip also has some slight indents where your trigger finger and thumb rest. This aids in getting a proper trigger pull for those with smaller fingers. It also helps with hitting the large magazine release. Being fairly large, the mag release size is nice and very useful. Helping to get rid of that awful Glock knuckle, is a slightly undercut trigger guard. One of the few flaws I found with the Rapture is the lack of a rail at the front of the pistol. But, it also wouldn’t fit in standard G26 holsters if it had one. Lastly, there is a thin slide release. Amazingly, the slide release was way easier to use then I expected it to be.

  When GForce Arms says the Rapture is “heavy in glock compatibility”, it is. All of the internal parts are gen 3 Glock compatible, and some of the external ones. So if you want to change out the barrel, trigger, trigger bar, slide, end plate, and sights, you can. Just use any of the readily available gen 3 aftermarket parts. 

  The trigger in the Rapture is decent. It starts with a flat face with a little hook on the end. Yes, there’s the little safety inside the trigger. The flipper safety seemed a bit strong, but it didn’t keep the trigger from being pulled, so it works fine. I do like the little hook on the end of the trigger. It helps a little bit to keep my finger from sliding all the way down and rubbing against the inside of the trigger guard. Trigger pull is decent, for these types of striker fired pistols. The Rapture’s trigger does have a decent break, not mushy like some gen 3 triggers are. Trigger pull weight was 5.5 lbs on my trigger pull gauge. I thought the weight was decent for a carry gun. Besides, if you want it lighter, there are plenty of parts on the market to make it anyway you want.

  Sitting on top of the GForce Rapture’s frame, is a fantastic slide. Yes, the slide looks kind of blocky, until you get a good look at it. It has front and rear angled cocking serrations, These are fairly deep cut, not overly sharp, and slightly deeper at the top. These serrations work extremely well. They blend into the frame nicely and look good. Inside the slide is a nondescript barrel and dual recoil spring system. Back on top of the slide are metal fiber optic iron sights. The front is red, and the back are green, both feature anti-glare serrations. The Rapture uses standard Glock sights, a big plus if you want to change them out for higher profile ones. Why would you want higher profile sights? Because the Rapture comes cut for optics! But it doesn’t stop there. The Raptures slide is cut directly for both the RMR and RMSc (sheild) footprints. GForce Arms also includes locator pins to use with either optics. These pins also help minimize optic movement under recoil. A nice optic cover plate comes installed if you don’t wish to mount an optic on the Rapture.

  I ordered up a kydex holster for the Rapture. Once it showed up, I began carrying the Rapture on and off. The gun carries nicely with an IWB holster. Being that the Rapture is not big, that helped. Probably what helped the most is the thinness of the Rapture. One thing I noticed while carrying the Rapture was how the magazine's pinky extension stuck out more than I liked. GForce doesn’t have an option for a magazine without the pinky extension. So I proceeded to dremel off the extension on one of the magazines, making it flush fit. This helped a lot in how noticeable the pistol was under just a T-shirt. I thought the sandpaper texture might cause some discomfort when carrying. To my surprise, the texture didn’t feel bad against my skin. It is only a little bit noticeable to me. The Rapture makes a decent carry gun.

Modified flush fit magazine

  The Rapture comes with 2 magazines. I would have liked to see it come with 3. But since the Rapture can be found for under $350, that didn’t hurt me too bad. Plus, extra magazines are only $25. Both the magazines sent with the Rapture are steel and hold 12 rounds each. Both have that aforementioned pinky extension. The Rapture magazines are proprietary. Also not a deal breaker for me. Remember, P365 mags are proprietary also. I have had zero problems with the Rapture magazines. 

  Shooting the Rapture was a pleasure. The first thing I noticed was that it didn’t have as much felt recoil. Or at least less than I was expecting from a pistol this size. I shot it with the fiber optic sights. Those sights are really easy to pick up and fairly fast. I then proceeded to mount an optic up top. I used the RMR cut option and installed a Swampfox Liberty. With this combo, the factory iron sights just peek above the optic. You can still use them as back up irons, but just barely. I ran all different weights of 9mm through the Rapture, with both the irons and an optic. The only problem I ran into was some factory reloaded ammo that wouldn’t go into battery. Not the Rapture’s fault because all the factory new ammunition I used ran flawlessly. So I would say the Rapture has more of a match chamber. In fact, the pistol ran flawlessly with zero malfunctions through about 750 rounds. No, I didn’t clean it either. I didn’t run an accuracy test on the Rapture, but I did run a dot torture with it at 5 yds. The Rapture performed well, I didn’t. I also set up my A-Zone steel at 50 yds. The Rapture didn’t have any problems reliably ringing it. So I’d say it’s more accurate then I am. When shooting and manipulating the Rapture, I also noticed that it doesn’t have any sharp edges on it, at least if you don’t count the front sight. Overall, the Rapture exceeded what I was expecting

  I really hope the GForce Arms Rapture stays around. It is a very well made, American, micro compact pistol. Plus it is affordable, hitting the streets at under $350. It has 12 round capacity, is thin, has lots of Glock compatibility, comes with 4 backstraps, and can mount any of the common red dot optics. I feel you can’t go wrong with the Rapture. Check it out at GForce Arms or your local dealer.

Firearms Insider Reviews - Key Points

Claim to Fame:

Sub-Compact handgun with a lot of Glock compatibility

Target Market:

Those wanting a quality micro-compact firearm at a decent price

Features, Benefits, and Specifications of this product:

  • Caliber: 9mm Luger

  • Capacity: 12+1

  • Comes with 2 Magazines

  • Frame Material: Textured Glass Filled Polymer

  • Comes with 4 Backstraps: 0°, 2°, 4°, & 6°

  • Optic Cut for RMR or RMSc footprints

  • Sights: Fiber Optic - Red Front / Green Rear 

  • Barrel Length: 3.25"

  • Trigger: Flat Face with hook

  • Weight: 22.5oz with empty magazine

  • Width (Overall): 1.12”

  • Height: 4.7” without magazine

  • Length (Overall): 6.62” 

  • Highly Glock Compatible, most parts are interchangeable 

  • Uses Glock sights

  • Comes with carry case that’s cut for optics

  • Made in USA

  • Assembled and tested in Reno, NV

  • Lifetime Warranty 

What other aesthetic options or finishes are available?

Flat Dark Earth 

What others are saying?:

Nothing found as of publishing`

Link to other reviews:

Outdoor News America

Price point:

MSRP = $379.00

Retail = $329.00 at Global Ordnance or Guns.com 

I need it now! Availability:

Global Ordnance, Guns.com, or your local FFL

Our Rating:

Pros:

  • Price

  • Glock compatibility

  • Optic cut with pins

  • Fiber Optic steel sights

  • Backstraps

  • Large mag release button

Cons:

  • No accessory rail

  • No flush fit magazines

Score: 8.00 Great

Favorite Link:  SwampFox Liberty Review   

Lone Wolf Dusk 19

Ammo for this review was sponsored by our friends over at

Target Barn

  Lone Wolf Arms has been making Glock compatible handguns for years now. They recently introduced their Dusk 19 handgun. The Dusk is their newest generation of pistols with a ton of great features added in. The Dusk 19 line has a bunch of different options, from a “stock” style pistol to threaded barrels with suppressor height night sights. Lone Wolf also has various color options for the Dusk 19. They sent out one with a FDE slide and ⅓ co witness sights for us to review. 

   When I say the Dusk 19 is Glock compatible, here’s what I mean. The Dusk 19 is compatible with G19 parts, and therefore, uses those styles of parts. But, it is definitely NOT a G19. Yes, the size is similar, but that is about it. The Dusk 19 specs are below in the Features & Benefits section, so you can read them there. However, there are some interesting features of the Dusk 19. It uses a Gen 4 magazine release. This gives it the ability to be reversed from side to side. So if you’re a lefty, Lone Wolf has you covered. The Dusk 19 also has Glock Gen 3 parts compatibility. It also uses G19 magazines. I used a variety of mags, including the 2 KCI mags that came with the pistol. They all functioned flawlessly in the Dusk 19. Lone Wolf also gave the Dusk a 19° grip angle. I’m a big fan of the 19° grip angle, as the pistol points really well for me. In addition to the grip angle, the Dusk also includes both a curved and a straight backstrap. I left the smaller, flat one on the pistol as my hands are not giant. If you need to mount accessories up front, the Dusk 19 has a standard picatinny rail. This makes it more compatible with various lights, as well as other accessories. 

  Lone Wolf took the most common aftermarket frame upgrades and included them on the Dusk 19. Not just a few, either, but a whole bunch. The first thing I noticed about the Dusk 19 was its aggressive texture. I love aggressive texture, mostly, and the Dusk 19 did not disappoint. This texture is everywhere. Both on the grip panels, the front of the grip, and on the 2 backstraps. It is also on the frame where you would rest your thumb or trigger finger. I really like this aspect for the ability to “feel” where your trigger finger is when not shooting. A note about those 2 backstraps, they have a place for a spare 2032 battery built into them. That way you can always have a spare battery for your optic. The Dusk 19 also received a decent beavertail to help with that annoying slide bite. The grip has a built-in magwell, not a huge one, but better than not having one. Lone Wolf also put a pretty good size undercut in the trigger guard to help you get a higher grip. Mounted up top the frame is a slightly extended slide release. It's not one of those that sticks way out, but it gives just enough to easily use. Lastly, the Dusk 19’s grip, as a whole, feels very compact in the hand. This grip is fairly short front to back, and not very wide. It even fits smaller hands pretty easily. Lone wolf did a great job designing the Dusk 19’s frame.

  Features still abound on the top side of the Dusk 19 too. The slide has front and rear manipulation serrations. These serrations are deep enough and sharp enough to use in any condition mother nature might throw your way. There’s a textured cover plate. The texture on the plate probably helps reduce glare, if nothing else, it looks good. Moving to the sights, the Dusk 19 has Night Fision ⅓ co-witness irons. The front sight is tritium and has a green ring around it. The rear is blacked out with serrations. In daylight, the green ring helps to focus your front eye on the sight. I really like the Night Fision sights, they work well. Now for the kicker, the Dusk 19 comes cut for mounting a reflex sight with a RMR footprint. I like that Lone Wolf is using an “Industry Standard” footprint for optics and not using a plate system. From the factory, it has a cover plate installed that blends nicely to the slide. Moving up front, the Dusk’s frame also has a spacer in it that can be removed. This spacer is for those that want to run a gen 4 recoil system and slide. There's zero reason to do anything with it on this complete pistol. The fit and finish of the Dusk's slide is fantastic. It is nicely machined everywhere. It also fits the frame fairly tightly. This is not something I usually say about stock Glock pistols. This slide to frame fit will also help in the accuracy department. Hand cycling the slide is smooth like butter. The PVD coating on the slide should give it a long life span, not to mention that it looks great! 

  The only functional part left to talk about is the trigger. The Dusk 19 sports a flat trigger. This flat trigger is radiused on the edges, but not a lot. Therefore the trigger’s face has a lot of flatness to it. Lone Wolf also put a decent, wider than normal, trigger safety. The trigger safety is FDE to match the slide, while the trigger is black. It's sharp looking. The trigger safety also operates super easy, so you don't really even notice it. When I tested the trigger's pull weight, it came in at 5 lbs out of the box. After 1000 rds, it's about 4.5 lbs now. It has a decent trigger pull too, for a glock style trigger. There is very little stacking and it has a clean break. A notable nice feature of the flat trigger is that it breaks at approximately 90°. I was pretty happy with the Dusk 19's overall trigger performance. 

  As with everything, nothing is perfect. I did have a few minor things happen during testing. Most of the testing was done with 124g CCI Blazer Brass 9mm supplied by Target Barn. Around the 250 round mark, I had a stovepipe. No big deal. Then around the 900 mark, I had another one. This second one I attributed to the gun being dirty, since I hadn't cleaned it at all. The trigger also started getting gritty around 900 rds. So I decided the gun needed cleaning. After that, it ran fine again. I ended up running about 7 different types, and bullet weights, of 9mm through the Dusk 19. All of the ammo was brass cased. It functioned great with all the different ammunition types. I figure that only having 2 out of 1000 problems says a lot about how good the Dusk 19 is. 

  I really used the Dusk 19, no easy days for it. It went to a Steel Challenge match and ran better than the shooter, with iron sights. The aggressive grip really lets you get a hold on the gun and helps with managing recoil. Since it fits in G19 holsters, I had plenty on hand to use. I used an OWB for Steel and some drills. Then I install a red dot at the 500 rd mark. Gun still ran great. I ran some training drills using an IWB holster. Then I proceeded to shoot some Dot Torture drills. This gives me an idea how accurate the gun is, and how well I do at speed. Well, the Dusk 19 is pretty accurate, from what I saw. The decent trigger pull also allowed me to get some fairly quick, accurate shots. The Dusk's grip angle also makes it easy for me to pick up the red dot. The gun just shoots great and feels really good in my hands. 

  I also carried the Dusk 19. It carries and hides nicely. But that grip texture can get to your skin after a full day. That's the only flaw I found with the texture. But I'd rather have a decent grip texture, than have a smooth texture that feels nice on the skin. As mentioned, since it fits G19 holsters, your options are endless. Some of the previous Dot Torture drills were done from a IWB carry holster. I have no problem carrying the Dusk 19 since it is a reliable firearm. 

  If you are looking for a pistol that has a bunch of upgrades already done, the Lone Wolf Dusk 19 could be it. Yes it costs a little more than a stock G19, but you don't have to spend money on upgrading it. So you save in the long run. It functions great, has night sights, and just feels good in the hands. It really is a kind of “do all” handgun. Head over to Lone Wolf Arms if you want to check out the Dusk 19.

Firearms Insider Reviews - Key Points

Claim to Fame:

Compact pistol with lots of options built in

Target Market:

Those wanting a factory compact handgun with included upgrades

Features & Benefits of this product:

  • Reflex Sight Ready (RMR cut) with DUSK optic cover plate included

  • Interchangeable flat & rounded backstraps with 2032 spare battery holder

  • 19° grip angle

  • Stainless steel PVD coated barrel with DUSK profile

  • Flat trigger

  • Undercut trigger guard

  • Front & rear serrations for ease of chambering and press check

  • OAL: 6.95" 

  • Barrel Length: 3.90”

  • Height (without sights): 4.61" 

  • Non-Threaded Barrel Height (with sights): 4.94"

  • Upper Width: 1.00" 

  • Lower Width: 1.14" 

  • Magwell Width: 1.23" 

  • Weight (without magazine): 19.8/oz. 

  • Caliber: 9x19

  • LWA Nitride SS Guide Rod & End Cap

  • LWA Reversible Magazine Release Button 

  • LWA Extended Slide Stop Release 

  • LWA Extended Takedown Lever

  • Night Fision lower ⅓ sights: tritium front, serrated rear

What other aesthetic options or finishes are available?

There are a bunch of styles available - https://lonewolfdist.com/firearms/complete-pistols/dusk-19/

What others are saying?:

5/5 stars at LoneWolfArms

An Excellent pistol

The Dusk 19 really elevates Lone Wolf. Likely the most ergonomic frame out there, flawless performance. The trigger is carry-appropriate,

Link to other reviews:

The Truth About Guns review

Price point:

MSRP = $649.95 - $699.95

Retail = Approx $600

I need it now! Availability:

Lone Wolf Arms or your local Dealer

Our Rating:

Pros:

  • Ergonomics

  • RMR cut

  • Comes with decent night sights

  • Glock compatibility

  • Grip size

Cons:

  • Couple of malfunctions over 1000 rounds

  • Texture can be rough when carrying

Score: 8.00 Great

Vosteed Thunderbird

  When it comes to everyday carry pocket knives, there are a ton on the market. All of them have various features for you to choose from. Vosteed makes a good selection of knives to fit whatever you are looking for. The Vosteed Thunderbird is one of those edc knives that has plenty of features. The Thunderbird’s features will rival knives that are priced much higher.

  Vosteed’s Thunderbird is a unique knife. Not in the way it looks, or the materials used, but in the way it opens. The Thunderbird uses Vosteed’s “Trek Lock” opening system. Trek Lock is a multi-opening system that allows one to open the knife in 4 or 5 different ways. One is by using the thumb hole. Another is using the normal flipper, located on the spine of the knife handle. And yet another way to open it, is to use the front flipper, located on the lower front of the closed Thunderbird. Then, since the knife uses a button lock mechanism, one can push the button and flip the blade out. Lastly, which isn’t really a flip method, is to just fold the knife out like you would an old school lock blade. To close the blade, just push the button and close it however you see fit. I would like the button lock to be a little harder to push. I just feel that little bit of extra might help keep the blade from wandering out when in the pocket. Not that it did this, but I can get the blade to open by just flicking the knife downward, something I can’t always do with button lock knives. If you like to fidget with your knife, the Thunderbird can’t be beat for that. I even find myself opening and closing it for no reason. As you may, or may not know, I am a big proponent of multiple ways to open a knife. Mainly because if you need to open a knife in some odd place, or body position, your main way of opening it might not work. So the Thunderbird is a dream come true for me. 

  Blade steel is an important quality of any knife. The steel Vosteed chose for the Thunderbird is top tier. This particular Thunderbird uses M390 steel. M390 is pretty much labeled a “super steel”, at least for knife making. It is super tough and durable with high edge retention, which leads to a high wear resistance. What that means for you is that the Thunderbird’s M390 blade will stay sharp for a very long time. M390 also has high corrosion resistance. So when you are actually using it, if it gets blood, or other bad stuff on it, it won’t damage the blade as quickly. One downfall to all of this, is that it takes a lot more effort to sharpen the Thunderbird. I’m okay with this trade off since the knife stays sharper longer. Vosteed also offers some versions of the Thunderbird with Elmax or S35VN blades. I don’t think you can go wrong with any of the blade steel offerings of the Thunderbird.

  The handle of a knife is also important. Vosteed chose a Laminate GT-Mascus, or in simple terms, a G10 handle with a topographical pattern. This topo pattern is a black background with blue topo lines. Besides looking great, the Thunderbird’s handle shape is useful. The handle's spine has a slight curve to it. This makes it fit the hand fairly nice, even though it is a fairly sleek knife. It also has a decent choil built into the handle. That way you can really dig into the handle for a tight grip. The back flipper tab also meets up with this choil, extending it out a tiny bit farther. One notable thing is that the flippers jimping is slightly noticeable in the front of the choil. This gives the knife a little better grip on that index finger. The handle doesn’t have any real texture to it, but being G10, it still gives a great grip. Vosteed also designed the Thunderbird with a deep pocket clip. The clip’s mounting is inlaid so it doesn’t bind up when putting the Thunderbird in your pocket. It is reversible, but both options are tip up carry. Lastly it has a brass spacer at the rear. The spacer also includes a place to install a lanyard. The brass nicely sets off the color scheme and helps balance the Thunderbird out nicely.

  The last important design of the Thunderbird is the blade profile. Vosteed gave the Thunderbird a curved tanto style blade. It also has a harpoon style top structure. These two designs give the Thunderbird a really good “piercing” ability. More important to me, is that the tanto’s tip melds nicely with the belly of the knife. This makes it more useful than a regular tanto style blade. On the spine of the blade there is some jimping. The jimping is the Thunderbirds one downfall. It is fine and not deep enough to really aid in use. The Thunderbird also uses a shallow hollow grind, which gives it some good slicing ability. I typically don’t like tanto style blades, but the Thunderbird made me believe that there are good style tanto blades out there.

  Even though I haven’t had the Thunderbird for very long, I have used it. It is really good at just about everything. From slicing gummy bears, which is the real test of a knife's sharpness, to scraping off stuff from hard surfaces, the Thunderbird just performs. As Vosteed states, this is the fidget king when it comes to knives. The knife is SHARP. It also stays sharp thanks to the M390 blade steel. I’ve cut a lot of cardboard too, and the Thunderbird keeps slicing through it like soft butter.

  If you are looking for that do all edc knife, the Vosteed Thunderbird might be it. It has an excellent blade material and shape. There are multiple ways to open it, thanks to its Trek Lock. It feels good in the hand and has a silky smooth action thanks to its ceramic ball bearings. At $135, it is priced far below what you would expect to pay for something of this quality. So go check out the Vosteed Thunderbird, they probably make a version that you’ll like..

Firearms Insider Reviews - Key Points

Claim to Fame:

EDC knife with quality blade steel and multiple ways to open

Target Market:

Anyone wanting this style of quality in a folding knife

Features & Benefits of this product:

  • Trek lock opening - Front Flipper | Back Flipper | Thumb Hole | Fuller

  • Blade Length: 3.25" | 82.55 mm

  • Overall Length: 7.73" | 196.34 mm

  • Blade Width: 1.10" | 27.9 mm

  • Blade Thickness: 0.118" | 3.00 mm

  • Blade Material: M390

  • Blade Grind: Compound

  • Blade Style: Tanto | Harpoon

  • Blade Finish: Black Stonewash

  • Hardness: HRC 60±2

  • Handle Length: 4.48" | 113.79 mm

  • Handle Width: 1.17" | 29.72 mm

  • Handle Thickness: 0.472" | 12 mm

  • Handle Material: GT-Mascus (G10 topo pattern)

  • Weight: 3.34 oz | 94.70 g

  • Pivot Assembly: Caged Ceramic Ball Bearing

  • Pocket Clip: Tip-Up Reversible | Stainless Steel

  • Knife Type: Manual Folding

  • Backspacer Material: Brass

  • Button Material: Stainless Steel

What other aesthetic options or finishes are available?

https://www.vosteed.com/collections/thunderbird

What others are saying?:

4 out 5 stars at Vosteed.com

3.25" m390 thunderbird

Very pleased with this knife. I also have a Vosteed Gator that I love. I like this smaller version of the thunderbird and find it the perfect size for daily carry. Every deployment option works exactly as it should. The knife came sharp (although I sharpened it to my liking) and perfectly centered. No issue with the button lock unscrewing or with the "spine whack" test that have been a topic for the previous thunderbird model. I wish the detent was a little stronger; however, it is a great knife that will perform well for daily tasks. Highly recommend it.

Link to other reviews:

Nothing But Knives

Price point:

MSRP = $135.00

Retail = Same

I need it now! Availability:

Vosteed

Our Rating:

Pros:

  • Multiple ways of opening

  • M390 blade steel

  • Button Lock

  • Ceramic bearings

  • G10 handle

  • Looks

Cons:

  • Button lock could have a little more strength

  • Shallow Jimping

Score: 8.50 Great

Favorite Link:  Viridian RFX 45 review

Primary Weapon Systems MK116 Pro Upper

 When it comes to AR upper receivers, there are a ton to choose from. You can get dirt cheap, or super hi-end. There’s also different ways for the firearm to cycle those upper receivers. One of those is the long stroke gas piston. Which leads us to Primary Weapon Systems (PWS for short). Primary Weapon System has been making long stroke gas piston AR uppers for some time, as well as complete rifles. PWS is well known for their long stroke gas piston AR’s and upper receivers.

  Primary Weapon Systems sent me one of their MK116 Pro Upper receivers. Which version they sent isn’t as important as how the upper operates. As all of the PWS uppers use the long stroke gas piston for operation. The long stroke gas piston operates differently than your standard AR’s direct impingement system. Instead of using the gas to cycle the Bolt Carrier rearward, the PWS long stroke gas piston uses a piston that is, essentially, directly hooked to the BCG through the piston rod. When gas comes into the gas block, it directly pushes on the piston to cycle the action. This gives a few advantages over the normal direct impingement system. For one, the gun runs cleaner because all the gas isn’t being directed directly into the action. It also allows the action to run cooler, since the hot gas isn’t being directly blown into the action. A big plus if you are running an upper on a full auto gun. Lastly, the action can tend to run smoother because all the operating parts are fixed together. There are also a few downsides to a long stroke piston upper. They can weigh a little more. The PWS upper is only a few ounces heavier than my comparable DI upper, so it’s not a lot of extra weight. The only other notable thing is that it comes apart differently than a DI upper. Not a big deal at all, just different.

  The PWS MK116 Pro upper has a lot of great features. First off, I’ll mention that I received the 16” barreled version. This is important to note because it uses a mid length gas system for the piston. It also has a 15” M-Lok handguard. The handguard is a little different then what most people are used to. This is because it is missing a small chunk of the top picatinny rail, or basically one lug of the rail. This lug is missing so that you can easily adjust the 3 position gas block. The MK116 also runs a slick side upper, so no forward assist. There is a small shell deflector on it to keep the ejected brass from hitting you, but it will hit your camera man in the face. This particular upper came with an A2 birdcage. If you want flash suppression, the A2 birdcage works very well. Lastly, the PWS MK116 comes with a Radian Raptor charging handle. I really like the Raptor charginging handles, PWS made a good choice in using them. 

Staking on Carrier bolts is different due to long stroke piston setup

  PWS gave the long stroke gas piston uppers, and firearms, a 3 position gas block. As mentioned earlier, this is easily adjusted through the handguard. One can even use the tip of a bullet to adjust it. The 3 positions are labeled 1,2,3, and “X”. All 3 positions have a detent and click to them. The X position is for disassembly and cleaning, it’s not a click adjustment. Position 1 is for unsuppressed use, or normal everyday use for those without a suppressor. Position 2 is for suppressed light loads or low back pressure (flow through) suppressors. Position 3 is for suppressed heavier loads or higher back pressure suppressors. I did try out all 3 positions. Position 1 works exactly as advertised. Position 2 would eject rounds without a suppressor, most of the time, Position 3 would not cycle without a suppressor. With my 556 suppressor, position 3 was spot on. Positions 1 and 2 had a bit of force behind the ejection pattern. I really like how PWS gives you a simple, yet effective, way to adjust the upper for suppressed and unsuppressed use. Through all my testing on the PWS upper, I had zero malfunctions, not counting the ones I caused by using the wrong gas position (I had to test them). I also used a variety of ammunition types and brands for testing, both suppressed and unsuppressed.

  Being that the Primary Weapon Systems MK116 was just a complete upper receiver, I needed something worthy of mounting it on. I ended up using an Aero Precision lower. This lower has a few options that make it a great companion to the PWS upper. The lower has a Blackout Defense Zero trigger installed in it, a VZ stipple grip, and an ambi safety selector. The trigger is what really makes such a great combo with the PWS long stroke piston. You can shoot this rifle super fast if you want to. Also, I needed to have some way to aim the rifle. I ended up using a 1x prism sight. Well, I did have a 1-6x on it at first, but I took it off in favor of the prism. The last thing I did to enhance the PWS upper was to install some NILE grip panels and a sling. The NILE panels use a M-Lok attachment, so they mounted up super easy to the PWS M-Lok rail. I had to use a M-Lok QD attachment for the sling. This particular PWS upper doesn’t have QD mounting points built into the handguard, that’s not a big deal for me, but it would be nice. I was really happy with how the PWS upper worked in conjunction with my lower receiver. The fit to the lower receiver was a bit tighter than what I would call “normal”, but not tight enough that it was hard to install on the lower. The PWS upper, when mated to my lower, made a really nice rifle.

  Anyone looking for a great way to upgrade an AR rifle, needs to look into the Primary Weapon Systems long stroke gas piston uppers. The PWS system works very well. The action is super smooth. The piston system is robust and will keep your rifle cleaner than the original gas system does. If you are using a suppressor, it also keeps the blowback gasses out of your face. So if you are searching for a top tier upper receiver, do yourself a favor and go check out what Primary Weapon Systems has to offer.

Firearms Insider Reviews - Key Points

Claim to Fame:

Long Stroke Gas Piston Upper

Target Market:

Those wanting a super reliable gas piston rifle

Features & Benefits of this product:

  • Operating System: PWS Long Stroke Piston System, 3 setting Adjustable Gas Regulator

  • Caliber: .223 Wylde

  • Barrel Length: 16.1”

  • Gas System Length: Mid-Length

  • Barrel Twist Rate: 1:8

  • Muzzle Device: A2 Flash Hider

  • Upper Receiver: PWS Proprietary Piston Upper, 6061 extrusion, Anodized

  • Handguard: PWS M-Lok™ 15” Handguard (1.7” width, 2.25” height)

  • Charging Handle: Radian Raptor™ Ambidextrous Charging Handle

What other aesthetic options or finishes are available?

PWS has a ton of different uppers, all are gas piston

What others are saying?:

Not much found

Link to other reviews:

Pew Pew Tactical full rifle review  

Price point:

MSRP = $824.95

Retail = Same

I need it now! Availability:

Primary Weapon Systems

Our Rating:

Pros:

  • Long Stroke piston

  • Radian Raptor charging handle

  • Adjustable gas block

  • Cut-out in handguard for gas block adjustment

  • Quality

Cons:

  • Cut-out in handguard for gas block adjustment

  • Proprietary system

  • Pricey

Score: 8.00 Great

Lone Wolf Ultimate Adjustable Trigger

  When it comes to Glock triggers, everyone has their opinion. I personally don’t hate them, but I am always looking for a better Glock style trigger. When Lone Wolf Arms contacted me about doing some product reviews, my first thought was “try one of their triggers.” That led me to the Lone Wolf Ultimate Adjustable Trigger. I’ve wanted to try this trigger out for some time due to its adjustability. 

  The Lone Wolf Ultimate Adjustable Trigger is a Glock replacement trigger. It is available for anything except Gen 5’s. I received a black trigger with the trigger bar attached. You can get just the trigger only, if you don’t need another trigger bar. The Ultimate Trigger can also be had in a variety of colors. Because I was looking for a fairly light trigger pull, Lone wolf also sent me some of their other trigger enhancement parts. These included: a connector kit, which includes 3 different 3.5lb connectors and a 6lb trigger spring, their plunger kit, and a lightweight striker kit with a 4lb spring. I installed the trigger and the Lone Wolf 3.5lb target connector.

  As you may have figured out from the name, the Ultimate Adjustable Trigger is adjustable. After installing the trigger into your pistol, you can adjust the pre and over travel of the trigger. This is done to eliminate as much pre and over travel as possible, giving you the shortest trigger pull possible. There are 2 tiny set screws in the trigger itself. These set screws do not come installed. I did install them, with some vibra-tight to keep them from coming loose, and also to be able to re-adjust them later, if needed. Probably one of the coolest things, with the Ultimate Adjustable Trigger, is that you can get to these adjustment screws without taking the trigger out. Just take the slide off and you can get to both of them. Lone Wolf has some decent instructions for adjusting the trigger, so I won’t go over them. You can find them HERE if interested. I was really pleased with how much pre-travel I was able to take out of the trigger. My over-travel wasn’t much anyway, so adjusting it only took out a tiny bit. 

  The Ultimate Adjustable Trigger uses a curved shoe. This curved shoe isn’t just curved, it is also radiused around the face, similar to a factory Glock trigger. The big difference is that the Ultimate Trigger also has a flat between those radiused edges. The Lone Wolf feels better to me. Maybe because it is machined to be smooth? Or, maybe its curve is better shaped? Or maybe its the flat? Either way, it has a really nice feel to it. No, it is not available as a straight trigger option for those who are going to ask. When I went to install the trigger, I also installed a 3.5lb connector. Between the trigger and the connector, the trigger pull weight dropped from 6lb’s to 4.5lb’s. That was with just those 2 parts. The shorter actual pull of the trigger also made it much more pleasant to use. 

  When using the Polymer 80, that I installed the Ultimate Adjustable Trigger in, it just feels better. The trigger was a great improvement over the stock one. I can shoot faster due to the shorter travel. I’m probably more accurate since I’m not fighting a heavy trigger pull. The other parts I installed from Lone Wolf, like the lightweight striker, also help with making the gun even more reliable. I like what Lone Wolf did with their Ultimate Adjustable Trigger, it just works.

  Even though the Lone Wolf Ultimate Adjustable Trigger has been around for a long time, it is definitely worth taking a look at. Especially if you like curved shoe triggers. The adjustments are really what make the trigger so nice. Pair that with a Lone Wolf 3.5lb connector, and you will have a nice Glock style trigger for a reasonable price. If you are in the market for a better Glock trigger, go check out the Ultimate Adjustable Trigger from Lone Wolf Arms.

Firearms Insider Reviews - Key Points

Claim to Fame:

Adjustable Glock Trigger

Target Market:

Those wanting a vastly improved Glock style trigger

Features & Benefits of this product:

  • 6061 Billet Aluminum shoe

  • Smooth, symmetrical shoe with large radiused edges

  • In-gun adjustability for pre and over travel

  • 2 piece design

  • Oversized safety lever

  • Safety lever is flush to the shoe for more comfort

  • 9/40 versions are intended for GEN 3&4 (DOES NOT FIT GEN5)

  • Comes with or without trigger bar

  • Made in USA

What other aesthetic options or finishes are available?

Lots of different colors

What others are saying?:

5 out 5 stars at Lonewolfdist.com   

Vastly improved…..

The feel and function of the trigger shoe is a vast improvement over the OEM. The bar, as received, had two burs at the contact point with the connector. Rough and gritty after install. So a few minutes with ceramic stones and polishing, all is well. Together with the target connector and springs the pull is silky smooth at 3lb 4oz. I did not install the take up and over travel screws. Overall well worth it.

Link to other reviews:

TFB review 

Price point:

MSRP = $77.95

Retail = Same

I need it now! Availability:

Lone Wolf Arms

Our Rating:

Pros:

  • In gun adjustable for pre and over travel (must remove slide)

  • Good trigger shoe shape

  • Lighter pull weight

  • Comes in color options

  • Available for a variety of pistol models

Cons:

  • No flat shoe option

  • Adjustment takes time

Score: 8.00 Great

Favorite Link:  Lone Wolf TimberWolf TWF-C review  

Vosteed Raccoon

  Vosteed has come on the market with a bunch of quality knives at affordable prices. The Raccoon is one of those. These knives give you good, useful features that won’t break the bank. If you are looking for an everyday carry knife, one that can handle a multitude of tasks, the Vosteed Raccoon might fit the bill. Let’s find out what this knife has to offer.

  The Vosteed Raccoon starts off with a crossbar style lock. The crossbar lock essentially locks the blade in place once open. I found it to hold the blade in place for everything I used the knife for, from normal cutting to scraping off tape. The crossbar lock on the Raccoon is spring loaded and located toward the top of the handle, near the pivot. Once the blade is locked in place and you wish to close it, just slide the crossbar back toward the rear of the knife to release the blade. You can use either side of the crossbar, or both, it’s really just personal preference. Amazingly, this is my first crossbar lock and I really like how it works.

  More important than the lock style, is the Raccoon’s blade style or shape. The Raccoon uses a flat ground 3.25” drop point blade made from 14C28N steel. Vosteed used a 3 to 1, length to width, ratio on the blade. I really liked what they did with the blade shape, it just works. If you are worried about the blade steel, it has held up extremely well. The blade came razor sharp. So sharp that I cut myself within the first few minutes of receiving it. I have had to sharpen the blade since then, but that is mainly because I was scraping off tile grout with it. I have two complaints about the blade. One is the choil. Yes, it allows one to choke up on the knife, but sometimes it can get caught on the edge of something, like a box flap. The next has to do with the jimping on the spine of the blade. It is too close together and not deep enough. It really doesn’t help much. Besides those two items, I really do like the Raccoon’s blade shape and style.

  I probably should mention how the Raccoon opens. Vosteed gave the Raccoon your everyday thumb stud opener. It has a thumb stud on both sides of the blade, so no matter what hand you use to open it, it will work. This thumb stud is in a good location and makes for opening the Raccoon very easy. One can also use the crossbar lock to open the knife. Just pull the crossbar back and the blade will fall open due to gravity. Or you can flick it out after sliding the crossbar back. Part of the reason the Raccoon opens so easily is its caged ceramic ball bearings. I always like a knife that has more than one way of opening it and one that opens smoothly. The Raccoon does both of those with ease.

  Moving back from the blade, we get into the handle. The handle on the Raccoon is made from micarta. The micarta gives the handle a nice feel. Being micarta, it naturally has a little bit of texture to it. Because of this, the micarta handle never felt slick to me and always gave a decent grip. The Raccoon also has a deep pocket carry clip. It’s only tip up, but can be moved to the other side. The clip is inlet where it screws to the handle so it slides smoothly in and out of your pocket. If you like lanyards, Vosteed put a hole in there for one. I was also pleased with the handles shape, it allowed me to really hold onto the knife. If you are not into micarta, Vosteed also offers the Raccoon with G10 handles.

  The Raccoon came in a nice little metal tin. Inside the tin was a little zippered case with the Raccoon inside. Vosteed also included a patch, sticker, and cleaning cloth. But probably more important, they included replacement springs for the crossbar lock. Not because they break, but because they like to go flying if you completely dismantle the knife. 

  I was pleasantly surprised with the Vosteed Raccoon. For a $50 knife it has some great features. But besides that, it cuts really well. I attribute its cutting ability to the blade shape. This makes the Raccoon a great EDC knife. It just does everything well. The Raccoon is now in my rotation of EDC knives. If you are looking for something sharp to carry around, I would look into what Vosteed has to offer. The Raccoon really fits the spirit of the animal it was named after.

Firearms Insider Reviews - Key Points

Claim to Fame:

Crossbar lock EDC knife

Target Market:

Anyone wanting a decent pocket knife that doesn’t cost a fortune

Features & Benefits of this product:

  • Overall Length: 7.60" | 193.12 mm

  • Blade Length: 3.25" | 82.55 mm

  • Blade Width: 1.07" | 27.27 mm 

  • Blade Thickness: 0.125" | 3.20 mm

  • Blade Material: 14C28N

  • Flat ground

  • Drop Point Blade

  • Blade Finish: Black Stonewash

  • Hardness: HRC 60±2

  • Handle Length: 4.36" | 110.75 mm

  • Handle Width: 1.10" | 27.95 mm

  • Handle Thickness: 0.49" | 12.4 mm

  • Handle Material: Micarta

  • Weight: 3.04 oz

  • Pivot Construction: Caged Ceramic Ball Bearings

  • Pocket Clip: Stainless Steel (Tip-Up, Right/Left Carry)

What other aesthetic options or finishes are available?

Too many to list, check them out at Vosteed.com

What others are saying?:

Jacob J. - 5/5 stars @ Vosteed.com

My favorite knife, hands down.

I have three Raccoons in varying colors. They're all butter smooth, razor sharp and have great ergonomics. For the price point, it's absolutely my favorite pocket knife and I plan to buy more for family members. The fit and finish is phenomenal for a $60 knife, and the presentation with aluminum box, polishing cloth, and zipper case is great at this price point.

Link to other reviews:

TechWriter Review    

Price point:

MSRP = $59.00

Retail = $49.00 at Knifecenter      

I need it now! Availability:

Vosteed or KnifeCenter

Our Rating:

Pros:

  • Blade profile

  • Sharp

  • Micarta Handle

  • Crossbar lock

  • Price

Cons:

  • Jimping is not great

  • Blade Choil

Score: 7.50 Good

Favorite Link:  SwampFox Liberty review   
,

Gideon Optics Judge

,

  Another red dot sight manufacturer has entered the arena. This new sight company is Gideon Optics. Gideon has come on the market strong with an assortment of micro and mini red, and green, dot sights. I’ve known the owner of this new optics company for some years now, so I am excited to get into the “Judge” red dot that they sent out for review. The Judge is Gideon’s micro red dot reflex sight and uses the RMSc mounting footprint.

  When the Judge arrived, I was excited to mount it up. Part of the reason I was excited is because I was looking for a red dot for my G43ish carry gun. The Judge fit that bill nicely as my G43 slide was already cut for a RMSc style sight. The other half of the excitement came from the Judge's auto on/off ability. In today's market, I see no reason why a red dot shouldn’t be auto on/off. Gideon also includes 4 different pairs of mounting screws. So you should have something that fits. More important, in my opinion, is that Gideon also includes a sealing plate with the Judge. This is important since the Judge uses a bottom load battery. The sealing plate does just that, it seals the battery from moisture and dust.

  The Judge has an option for either a red or green dot. I chose the red dot because my eyes just seem to pick it up faster. The Judge uses a 3 MOA dot size, which is a good size for all around use. If you have an astigmatism, like I do, the dot will probably look larger because of the “flare”. Don’t worry, the Judge’s dot is fairly clear in pictures, so I know it’s me and not the sight. To adjust the 10 brightness settings, the Judge has a brightness up button on the left side and a brightness down button on the right side. I actually like this better than the red dots that have both the up/down on the same side. There’s just no doubt which button I am pushing. With the Judge, you get 90 MOA of total adjustment for windage and elevation. More importantly is that the Judge has actual clicks for the 1 MOA adjustments. These clicks are not something you find in competitors' products, but the Gideon Judge has them.

  Construction of the Judge is pretty sound. You get a 7075-T6 aluminum housing, not the less durable 6061. It is also waterproof to 1 meter for 30 minutes plus. Let’s just say that I have not broken it yet. The Judge also only tips the scales at around 0.6 ounces with the 2032 battery. Probably more important to the user, is that the judge has a window size of 16x21mm. This size is really nice for such a small reflex sight. I was able to get a good sight picture fairly quickly. Essentially, the window is big enough to make it easy to find the red dot. 

  The Gideon Judge just runs. I can’t seem to get the Judge to stop. It has given me zero problems since day one. It’s bright with very little tint to the lens. It has held zero through all my abuse. Granted, I didn’t drop it on concrete, but I also don’t want to actually break it just to break it. I love the click adjustments. In all, I have had a good shooting experience with the Judge.

  If you are in the market for a micro red dot, definitely give the Gideon Judge a look. Maybe even judge it compared to others in this market space. It has some great features at a respectable price. I might even give it style points for its looks. Even if you are looking for a different style of red dot, Gideon Optics might have what you want, so go check them out.

Firearms Insider Reviews - Key Points

Claim to Fame:

Small Red or Green dot that fits RMSc slide cuts

Target Market:

Anyone wanting a small red or green dot optic

Features & Benefits of this product:

  • Magnification: 1x

  • Lens Dimensions: 16mm tall x 21mm wide

  • 7075-T6 aluminum body

  • Elevation/Windage adjustment range: 45 MOA (Total 90 MOA)

  • Click Value: 1 MOA per click

  • Circle Dot Reticle: 3 MOA Dot

  • Parallax Free: Beyond 33 yards

  • Red Dot Brightness Setting: 10 levels (8 visible, 2 NV compatible)

  • Power Supply: 1x CR2032 3V Lithium battery

  • Run Time: approx 40,000 hrs

  • Auto Wake/Sleep: 225 Seconds after no movement

  • Shockproof & IPX7 Waterproof

  • Dimensions: (LxWxH) 41mm x 25mm x 24mm

  • Weight (with battery installed): 0.6 oz (approx.)

  • 1913 picatinny rail mount and screws

  • T10 tool

  • Adjustment tool

  • Sealing plate

  • Cleaning cloth

  • One pair each of the following mounting screws: M4 x 0.7 x 10mm, M4 x 0.7 x 8.6mm, M3.5 x 0.7 x 10mm, M3 x 0.5 x 12mm

What other aesthetic options or finishes are available?

Green Dot Version

What others are saying?:

Dan @ OpticsPlanet

Very happy

I purchased this for my PSA 5.7 Rock. Could not be happier clear Len and crisp dot.

Link to other reviews:

Caleb Downing on YouTube   

Price point:

MSRP = $229.99

Retail = Same but use code “GGR” for 10% off at Gideon Optics

I need it now! Availability:

Gideon Optics or JSD Supply

Our Rating:

Pros:

  • Bright Dot

  • Actual click adjustments

  • Auto on/off

  • Includes Sealing plate

  • Includes various mounting screws

Cons:

  • Slightly fuzzy dot

  • Bottom Load battery

  • Only a 3 yr warranty

Score: 7.50 Good

Favorite Link:  Patmos Arms Judah slide review
,

Primary Arms SLx 3-18x50 Gen 2

,

  Quality optics have become affordable for most shooters in the last few years. One no longer needs to spend $1000, or more, to get a clear quality optic. Primary Arms has been aiding us shooters with these types of optics. Their new Gen 2 SLx 3-18x50 FFP is one of those. This optic has features that should make it cost twice the price. 

  The Gen 2 SLx 3-18 is packed with features. Coming in first is its First Focal Plane (FFP) reticle. Yes, this $500 optic has a FFP Christmas tree style reticle. So when you zoom in, all the reticle’s MIL marks stay the same. This allows you to hold over for bullet drops, or wind, at any reticle setting. This particular optic uses Primary Arms’ ACSS Athena BPR Mil reticle. I won’t go much into the reticle’s design as it uses MIL’s in a very useful pattern. But, the reticle is illuminated to help one see better in low light. It’s pretty bright for this size of optic. This ACSS reticle also uses a small center chevron, think triangle, for aiming. Most optics like this just use a small dot. The top point of the chevron can be used for very precise shots, more so than if one were to use an optic with a small center dot. The other nice aspect to this reticle is its built in ranging ladder. The ladder is in the upper right hand portion of the optic. This puts it out in the part of the reticle that is seldom used. I really like how Primary Arms designed the ACSS Athena reticle. It is easy to use, even for someone like me that is used to using a MOA reticle. I even mentioned to Primary Arms that they were starting to convert me to MIL reticle scopes. Part of that comment was due to the SLx 3-18x50.

At 18x, Tower Light is approximately 350 yds away. Light is also 15” wide for ranging purposes.

  Since I was talking about the reticle, let's go into the optics themselves. This SLx 3-18 gen 2 is exceptionally clear. This is why I say it far exceeds its class. I had zero problems with the clarity, even at its full magnification of 18x. I could easily make out 17 HMR holes in targets at 100yds. The crispness of the glass is also really good, though I did find it to drop off a little at longer ranges and at higher magnification, but it never caused any problems. I did find the parallax adjustment to be a little touchy. At least when focusing the parallax adjustment on targets between 200-400 yards. They were the hardest to get focused. Other ranges didn’t seem to be as touchy, even the lower ranges like 15-100 yds. I will give the SLx credit for having a parallax adjustment that goes from 10 yds to infinity. Other than those minor issues, the SLx 3-18 gen 2 has great glass for the money.

  The function of the SLx 3-18x50 gen 2 has some outstanding features also. My absolute favorite is that this optic has a true zero stop on the elevation turret. Once you find out where your zero is, just set the stop and you will never have problems finding your zero again. No matter where you adjust to, just turn the back down until it stops, you are now at your zero setting. The turrets have been upgraded over the first gen SLx 3-18. They are larger so you can get a better feel on them. This also makes them easier to turn. These turrets also have fairly good clicks to them. You can feel and hear them. The elevation turret is a target style and not capped. The windage turret is capped….unless you want it to be a target style turret. Primary Arms includes a target style turret that you can replace the capped one with. So essentially you have the best of both worlds. I typically don’t dial for windage, so I left the turret in the capped version. One other feature, that Primary Arms added to the SLx 3-18 gen 2, is their changeable throw lever for the magnification ring. Instead of being stuck with whatever the optic company gives you, Primary Arms gives you options. The throw lever, that comes installed, is fairly tall and makes it easy to adjust magnification. But, if it’s not your thing, just take it off, or get one of the other throw lever options.

  I installed the SLx 3-18x50 gen 2 on my semi-precision 243. Being that the 243 is not your standard 1000 yd cartridge, more of a 800 yd one, I thought this magnification range would be a perfect fit for it. All I can say is that it worked out great on this rifle. Don’t get me wrong, the SLx 3-18 gen 2 is perfectly capable of going out to 1000 yds clearly. My eyes are old and like a little more magnification when reaching out farther. A while back, 10x was adequate for 1000 yds. I view a 3-18 as more of a mid to long range optic. If I was looking for something in the longer range category, I’d look into the Primary Arms 5-25x56.

  Primary Arms did a great job designing the SLx 3-18x50 FFP gen 2. Basically it reaches above its pay grade and into the realm of optics that cost twice its price. It has good optical clarity and a top notch reticle. The SLx 3-18 gen 2 also functions extremely well with those large turrets and zero stop. It is a little on the heavy side, but for $500 you can’t go wrong. So if you think you might need a top notch, value priced optic, in the 3-18 power range, do yourself a favor and check out the SLx 3-18x50 gen 2 from Primary Arms

Firearms Insider Reviews - Key Points

Claim to Fame:

First Focal Plane mid-power optic with a great feature set

Target Market:

Precision shooters and hunters

Features & Benefits of this product:

  • CR2032 3V Lithium Battery

  • Eye Relief: Low: 3.5in. / High: 3.9in.

  • Field View at 100: Low: 35ft. / High: 5.9ft.

  • First Focal Plane

  • Red Illuminated Reticle with 6 brightness levels

  • Length: 13.6 in.

  • Magnification: 3X - 18X

  • ACSS ATHENA BPR MIL Reticle

  • 0.1 Mil Click Adjustment Value

  • Total Elevation Adjustment: 100 MOA

  • Total Windage Adjustment: 64 MOA

  • 30mm Tube Diameter

  • Weight: 32.04 oz

  • Zero Stop Elevation Adjustment

  • Lifetime Warranty

What other aesthetic options or finishes are available?

Apollo 6.5cr/224v and 308/6.5g reticles     

What others are saying?:

Nothing found as of publishing

Link to other reviews:

Hunt Fish Shoot on YouTube  

Price point:

MSRP = $499.99

Retail = Same

I need it now! Availability:

Primary Arms

Our Rating:

Pros:

  • Clear Glass

  • Price

  • Zero Stop

  • Larger Turrets

  • Extra Dial Turret for Windage

Cons:

  • Parallax adjustment is touchy

  • Heavy

Score:  8.00 Great

Sencut Serene

  When looking at an EDC knife, your average person tends to want quality at an affordable price point. Sencut knives just might be what these people are looking for. They sent out the Serene model for me to use and review. I opted for the blue handled version with the satin finished blade, but they have other color options available. 

  The Sencut Serene is a button lock, flipper style knife. It also has thumb studs on it for opening, not just the flipper or button. This means that there are 3 ways of opening the knife up. Either flip it out using the flipper hump on the back side of the handle, or by using the thumb stud. Being a button lock knife, one can also push and hold the button in, then flip the knife out. I am a person that really likes having multiple ways to open an EDC knife. You never know when your normal way of opening it just won't work. Being a button lock knife, and a flipper, the button is spring loaded so that it catches the blade at full extension, and locks it in place. I found the Serene’s button lock to work well. The blade also locks up tight. The other great aspect of the Serene is how smooth it functions. Those ceramic ball bearings make it feel like you are getting a much higher price range knife.

   The heart of any knife is its blade steel. The Serene uses D2 steel at a hardness of 59-61. D2 is an excellent choice for anyone wanting an everyday use knife. D2 is not considered stainless steel, so you will need to clean it and oil it every so often. But, D2 will give you good edge retention and toughness. Not as much as high end steels, but the Serene is a budget knife that performs above its pay grade. Because the D2 blade is fairly tough, it takes a little more to sharpen it, but that also means that it will stay sharp longer. I am a fan of D2 steel in knives, and Sencut made a good choice using it in the Serene.

  Since we are on blade steel, let’s get into the blade itself. The Serene uses a 3.48” drop point style blade. So it’s not tiny. Basically it is curved up from the blade's belly to become a point. The Serene uses a shallower curve than what I would call your typical drop point blade. It doesn’t really have a flat spot in the cutting edge, it just gradually curves upward to the point. I found the blade shape to be very useful for most of my cutting needs. Sencut also put some decent jimping on the top of the blade. This gives your thumb some grip on the top of the knife. The Serene’s blade is also very thin, making it easily slice through stuff. The flat grind on it also probably helps with that too. I am also a fan of the blade's thinness.

Worn Anodizing

Easily dinged up handle

  As with any knife, it usually needs some sort of handle or frame. The handles on the Serene are made from aluminum and anodized in different colors. Sencut did not put any texture on the knife's handles. They aren’t necessarily smooth, as there is, what looks like, a bead blasted finish. But they feel smooth to me. There is a finger curve cut out for your index finger. This does give some grip so your hand won't slip off the knife. The shape and smoothness of the handles does make for a comfortable feeling knife in the hand. One drawback, I found with the Serene, is that the anodizing wears off pretty easy. Especially around the edges. Dings show up pretty easily in the anodizing too  The Serene also has a tip up reversible carry clip. The clip is designed for fairly deep carry, and is decently strong to hold the knife in place.

  The Sencut Serene fits my style of EDC nicely. Its blade length fits in where I like them, somewhere between 3 and 3.5 inches. The thin D2 blade stays sharp and cuts nicely. The handle may be smoother than I like, but some people prefer a smoother handle. It’s also pretty lightweight. I really don’t think a person can go wrong with the Sencut Serene. The knife has a lot of good attributes, especially in the $50 price range. You can check the Serene out at Sencut.com.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Lightweight EDC knife

Target Market:

Those wanting a quality flipper knife that won’t break the bank

FNBs (Features & Benefits of this product):

  • Overall Length: 8.17" / 207.5mm

  • Width: 1.43" / 36.4mm

  • Overall Height (Include Clip): 0.68" / 17.2mm

  • Blade Length: 3.48" / 88.4mm

  • Closed Length: 4.69" / 119.1mm

  • Blade Thickness: 0.12" / 3mm

  • Handle Thickness: 0.47" / 12mm

  • Knife Weight: 3.43oz / 97.3g

  • Blade Material: D2

  • Blade Hardness: 59-61HRC

  • Blade Grind: Flat

  • Blade Finish: Satin

  • Blade Type: Drop Point

  • Handle Material: Bright Blue anodized Aluminum

  • Hidden Lanyard bar

  • Pocket Clip: Tip-Up, L/R

  • Clip Material: Stainless Steel

  • Screws/Thumb Stud Material: Stainless Steel

  • Pivot Assembly: Caged Ceramic Ball Bearing

  • Locking Mechanism: Button Lock

What other aesthetic options or finishes are available?

Blak, Red, or Grey

What others are saying?:

5 out of 5 stars on Amazon   

Very nice and extremely sharp!

This is my first Sencut knife. I purchased it because I have always enjoyed my Civivi knives, and I know they are from the same OEM. This knife came extremely sharp from the factory. It performed the paper cut test with almost no resistance and absolutely a razor clean cut. The thumb stud is a good size, but not too big as to be distracting or in the way. The flipper tab on the back is also very modest but quite functional. My wife who has zero experience with flippers was able to work both methods of opening first try. The button lock depresses easily, but not so easily that I would worry about accidentally unlocking the blade while working. The action is buttery smooth, and the detent is very nice. The knife is exactly the same blue color as the depiction. The blade is perfectly centered, and has no play left to right or up and down. I am very impressed with this Sencut knife and will be purchasing more from this brand in the future.

Link to other reviews:

Neeves Knives on YouTube   

Price point:

MSRP = $55.00

Retail = $46.75 on Amazon     

I need it now! Availability:

Sencut or Amazon

Our Rating:

Pros:

  • Sharp

  • Thin D2 blade

  • Button Lock

  • Flipper

  • Ceramic bearings

  • Deep carry pocket clip

Cons:

  • Anodizing wear

  • Smooth handle

Score: 7.50 Good

Favorite Link:  Angry Bear Arms sight review 

Primary Arms SLx 3x MicroPrism

  Many years back, fixed power optics were very common. They tended to be larger in size when compared to say, a standard tube style red dot. Fixed power optics have come back around thanks to the small magnified prism optics like the Primary Arms SLx 3x MicroPrism. The SLx is so much lighter and smaller than the fixed power scopes of the old days. The SLx 3 power prism also gives you plenty of new benefits that just weren’t available back in the day. So let’s welcome in the small, fixed 3 power optic of the future. Now offered in FDE to match all your tactical needs.

  Primary Arms set the bar high when they released the 1x MicroPrism, then they raised it with 3x and 5x models. They sent me out the 3x version in FDE. Fixed power optics have their place in the shooting world. With the SLx 3x you get a super small package size plus some magnification to see targets at mid range distances. Since the magnification isn't super overpowering, you can still use this optic up close. It also doesn’t weigh much, tipping the scales at just about 8 ounces. For being in Primary Arms’ SLx line of products, you get an exceptional value with super clear glass. 

  One of the great aspects of the Primary Arms 3x MicroPrism is its reticle. Primary Arms uses one of their ACSS reticles, or “Advanced Combined Sighting System”, in the SLx 3x. In particular, this is the Raptor ACSS reticle. The ACSS Raptor gives you ranging, bullet drop compensation, wind holds, and moving target leads, all in a simple to use red colored reticle. The reticle has an illuminated horseshoe around a center chevron (think triangle instead of dot). The ranging, wind and bullet drop then take up the reticle below the center chevron, these compensations are not illuminated. The illuminated section has 13 intensity settings, 3 of which can be used with night vision. Using the ACSS Raptor is really easy. The large horseshoe lets you shoot up close targets quickly, even though the SLx is a 3 power optic. The chevron and stadia then give you precision shots out farther. I found the reticle to be a good compromise between close and far range targets. Being a 3 power prism sight, I am a little slower at shooting an array of close in targets, but I am more accurate when out at farther distances. Primary Arms did a good job with the reticle on the SLx 3x MicroPrism. The illuminated part of the reticle is “daylight” bright, even in direct sunlight. If, for some reason, it does wash out a tiny bit, the reticle is etched into the glass, so you get your typical non illuminated black reticle anytime, even if the battery goes dead. 

  If you are worried that the SLx 3x MicroPrism won’t work for your firearm, don’t fret. Primary Arms gave the MicroPrism plenty of mounting options, and they all come with the optic. The SLx manual states 8 different mounting heights. This is from essentially rail height (1.1” to center of prism) to 2.075” to center of optic. There is also one other option. If you have a carry handle AR, fixed or removable, the SLx MicroPrism will mount directly to the carry handle. If you want to use a different mount than the ones supplied, The SLx MicroPrisms use an industry standard “Mini Prism” footprint. 

  One aspect of the Primary Arms MicroPrisms is their exceptional clarity. For the price you pay for one of these, you get extraordinary clear glass. I’ve also found that even though the eye relief is stated at 2.7”, it is very forgiving. Since the MicroPrisms have an etched reticle, they also don’t have the clarity problems for people with astigmatisms. Making the ACSS reticle super clear. Being that this SLx MicroPrism is 3 power, it also has a decent field of view at 100 yds, which is 38 ft. So you will see a 38 foot wide circle, when looking through the prism sight, at 100 yards. 

  The SLx 3x MicroPrism also has a few other features that need mentioning. First off, it uses Primary Arms’ “AutoLive” motion sensing on and off. So when you pick up the SLx prism, the reticle turns on at whatever brightness the knob is set to. After not sensing any movement for a few minutes, the optic goes back into a hibernate mode, where the reticle is off. Once you move the optic, the on cycle starts again. I absolutely love the AutoLive technology and it works fantastic on the Primary Arms’ MicroPrisms. This AutoLive also gives the 3x MicroPrism a battery life of around 29,000 hours. Which is fantastic for any magnified optic. The windage and elevation adjustments are also protected from being hit or accidentally turned. You can even adjust them using the rim of a cartridge. I’ve done it, it’s easier than looking through the range bag for a tool. 

  The Primary Arms SLx 3x MicroPrism fits in well for a fixed mid range optic. It allows close range work too. Everytime I look through one of the Primary Arms MicroPrisms, I am surprised by the optic clarity. Add in the AutoLive function and you have a great combo of features. So if you are looking for a small fixed 3 power optic, check out Primary Arms’ line of SLx MicroPrisms.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Small, lightweight fixed 3 power prism scope

Target Market:

Those wanting a small profile, fixed 3x sight

FNBs (Features & Benefits of this product):

  • FDE finish

  • 13 total illumination settings, 3 are NightVision compatible

  • Daylight Bright

  • AutoLive motion-sensing on/off battery saving technology 

  • Length: 2.95”  

  • Weight: 7.95 oz.

  • Illuminated and etched ACSS bullet drop reticle

  • Field of View: 38.0 ft @ 100 yds

  • 80 MOA Adjustment

  •  0.25 MOA Click Value

  • 8 Mounting Height Options

  • One CR2032 Battery (Included)

  • Up to 29,000 Hours on medium setting

  • Industry Standard Mini Prism Mount Footprint

  • Eye Relief: 2.7"

  • Lens Covers 

  • Lifetime Warranty

What other aesthetic options or finishes are available?

Black anodized, Griffin MIL reticle

What others are saying?:

5 out 5 stars - Devin at PrimaryArms.com

WOW, PRIMARY ARMS REALLY GOT IT RIGHT WITH THIS ONE!

This is Primary Arms Optic number 3 for me, but will definitely not be the last!

I got this optic for a lighter weight, simplified build. Got tired of dealing with heavy rifles and playing around with LPVO's, so this became the obvious choice. I was a bit skeptical about the fixed 3x magnification, but after zeroing it this afternoon I didn't have any issues taking shots at 100 and 150 yards, ran out of daylight to try any longer distances. However, I don't think I'll have any issues making hits out to 300–400 yards.

I know this is a "budget" priced optic, but I'm pretty impressed, the glass is really clear. The reticle is sharp and informative without being cluttered like so many optics are. Oh, and speaking of the reticle, the illumination is very bright on the maximum setting, much brighter than my LPVO and gen 1 Cyclops prism. I would say it's daylight bright, I actually ended up dropping it down to the 9th or the 10th setting to use during the day.

Link to other reviews:

Lynx Defense  

Price point:

MSRP = $319.99

Retail = Same at Amazon

I need it now! Availability:

Primary Arms

Our Rating:

Pros:

  • Clear

  • Bright ACSS reticle

  • AutoLive

  • Small size

  • Various mounting heights

Cons:

  • Reticle is small to see

Score:  8.00 Great

Favorite Link:  Primary Arms SLx 1x Prism review  

Z-Bolt Blazer LED & LEP lights

  When it comes to weapon mounted light, there are a ton of different aspects to choose from. Z-Bolt has a few options that are very interesting. Their lights lean high on the candela for maximum beam throw. Z-bolt also has options so that you can get a wider beam out of their lights. They sent both their LEP and LED lights to me for review.

  An explanation is probably due to the differences between the LEP and LED. Most of you have heard of, or used, a LED light. Not everyone has used, or seen, a LEP light. LEP stands for Laser Excited Phosphor. According to Z-Bolt: “The BLAZER employs a blue laser to fluoresce a yellow phosphor, forming a broad spectrum of white light.” Because of this, with an LEP light, you get a super focused white light beam. Think of a small spotlight, because when you shine it out into space, it looks just like a spotlight, there is zero spill over on this light. Now the LED light is just what you expect, a Light Emitting Diode type light. In the Z-Bolt LED light, you get a really good light throw, but still some spill to see things to your left and right. 

  As mentioned, Z-bolt sent two different lights, an LED and LEP. Both of the kits they sent are for weapon lights. These particular ones are for the “Scout” mounting platform. The LEP light kit that Z-bolt sent has a 18650 body, the LEP head, a clicker tail cap switch, 2-18650 batteries, a dual charger, 2 CR123 batteries, a “hot spot & fill” diffuser, and Red & Green predator filters. The LED kit from Z-Bolt is their Weapon and Handheld carry package. It includes a 18350 “scout” body, a handheld body, 2-18350 batteries, that same dual charger, a Thyrm switchback, clicker handheld tailcap, and a momentary only weaponlight tailcap. Z-Bolt makes different kits or stand-alone lights too, so whatever option you want, they probably have it. Z-Bolt also makes different tailcaps so that you can use a pressure switch, hot button, or one of those with a tailcap switch combo. The light heads, bodies, and tailcaps are interchangeable between all of their lights. So if I wanted to use the momentary only switch on the LEP weaponlight, I can. Another advantage to these kits is that the bodies, lightheads, and tailcaps are compatible with the Surefire M600DF/M640DF line of light parts, which is kind of the industry standard for thread pitches and allows the Z-Bolt parts to screw on.

  I won’t bore you with the specifications, as they are down in the “FNB” section, but I will tell you how each light performs:

LEP beam

  When you first turn on the Blazer LEP light, you immediately notice the bright spotlight effect. This light shines a super focused beam. If it’s on a wall close to you, it’s not much bigger in diameter than the light head itself. This is expected from a light that has a 315,000 candela rating. Even at distance, the beam does not spread out that much. The LEP also has a cool white light, not the harsh style that a lot of LED lights have.

Green Filter LEP

Approximately 450 yds, LEP

Diffused LEP

  The Blazer LEP serves a purpose for target identification at long range. Z-Bolt claims a 600 meter Positive Identification of Target (PID). Which I believe after using it. I found the LEP to be exceptional at it. So much so that I needed binoculars or a magnified optic to see what the Blazer LEP was illuminating, as you can see in some of the pictures. I was able to illuminate a tree at approximately 450 yards and make out the branches. Granted the picture is a little blurry, but the tree was in focus for me when looking through a rifle scope set to about 14 power. It would be real easy to see a person at that distance, and maybe slightly harder to see a hog or coyote, but it can still be done. The light throw on the Blazer LEP is just that great. Now if you need to throw some light off to the sides, the LEP comes with a “Hotspot & Spill” diffuser. This gives the light a 15 degree spill with a center hotspot. It also cuts the range of the light down to about 150 yards. This filter just screws on. The filter worked okay for me, I just didn’t care for how it limited the lights range. There are also different filter options available from Z-Bolt. They range from a dedicated 15 degree spill to a full 40 degree for CQB or full room illumination. Another benefit of the Blazer LEP is its ability to punch through photonic barriers like smoke, fog, or tinted windows. 

  Battery run time is also good on the Blazer LEP. Using the supplied 18650 battery, run time is 130 minutes according to Z-Bolt. Let’s just say that when I was taking all the pictures , I didn’t have to change the battery out. The 18650 bodied lights, like the LEP I am using, can also run on 2 CR123 batteries. This will limit the run time to 90 minutes. That is still a respectable hour and a half on store bought batteries. 

approximately 200 yds, LEP

  If you are using the LEP to predator hunt, the light kit that I was sent, has a red and green filter. I found the red didn’t illuminate all that well. If using it with night vision, it should be good and not so bright as to cause problems. Now the green filter was super bright with the naked eye. It really makes the LEP light look like a wide green laser. It has a really good throw to it also. I was able to identify stuff at 200 yds without problems. 

  For target identification at longer ranges, the Blazer LEP is great. If you want to see what's across the canyon in the pitch black of night, the LEP is for you. If you are looking for a general use weapon light, I would choose the Blazer LED below. But in the “see far away” white light market, my choice would be the LEP.

LED:

  If the LEP style of long throw light isn’t for you, don’t fret, Z-Bolt has a LED style light. The Blazer LED is touted as being a long throw LED light. It has a respectable beam throw, but still gives a 60 degree spill to the beam. This gives a “Hot Spot & Spill” style pattern, and it works well. Z-Bolt states target PID out to 200 meters. Since I was able to light up 200 yard targets, I do agree with them. A big advantage to the LED light is its spill. I can light up the inside of a room okay, but yet it still gives me a good beam throw for those mid range targets. If I could get a little more spill and still have the same light throw, I’d like the Blazer LED even more than I do. The Blazer LED is listed at 65,00 Candela and 650 lumens, which is why I get a good combination of spill and throw.

LED Spill and hot spot

  Z-Bolt sent the combo version of the LED light. That meant it came with a 18350 scout body and a handheld body. The 18350’s are a shorter 18650 and hence give lower length run times. This LED version only has a run time of 60 minutes. Still pretty good considering what you are getting as far as light output. If you aren’t looking for a combo, the LED lights can be had individually for a competitive price.

Tree line is around 150 yds, LED

LED

  I’m not going to say much about the weapon light version of the Blazer LED, because all the specs transfer over to the handheld version. The weapon light configuration just mounts to a rifle using the standard “scout” mounting platform. So off to the handheld version. The handheld configuration of the Blazer LED uses a separate clicker tailcap and body. Basically it’s smooth and void of mounting nubs. This configuration makes for a great handheld light! Plus it is only 4 ⅞ inches long. This is shorter than a lot of so-called EDC lights. It can also be used with the THYRM style of pocket clips. This particular kit came with the Thyrm Switchback. I didn’t use it as I am one who just lets the light float around in my pocket, which I probably shouldn’t. I’ve been pleased with the Blazer LED as an EDC flashlight.

  The Blazer LED is a decent white light. In either the weapon mounted configuration, or the handheld configuration, it performed well. I like it both as a handheld and weapon mounted light. The beam throw works great in either form. In the handheld configuration, the beam spill is fine for me. In weapon mounted form, I’d like a little more spill. Either way, the Blazer LED makes a good EDC or CQB light.

  If you are in the market for long throw lights, Z-Bolt might have what you need. The Blazer LEP’s extreme long throw really lets you reach out and identify targets. If you don’t need that much range, but still need some, the Blazer LED is a great option. I would consider both the Blazer LED and LEP to be top tier lights in any configuration. They even use industry standard mounting, battery bodies, and tailcaps, which makes choosing them, as an option, even easier. If you need a long throw, handheld, or weapon mounted light, head over to Z-Bolt Electro Optics and check them out.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Long throw weapon lights

Target Market:

LED - Those wanting a bright handheld light that also functions as a great medium range weapon light

LEP - Those needing to see or identify targets at long ranges

FNBs (Features & Benefits of this product):

LEP

  • Light on Target: 315,000 Candela

  • Run Time: 130 Minutes, 1 pc Z-Bolt 18650

  • Run Time: 90 Minutes, 2 pcs Z-Bolt CR123A 

  • FDA Laser Safety Class 1: Certified EYE-SAFE

  • Max Beam Throw: 1,100 meters (ANSI FL1)

  • Battery: 2 pc 18650 - 3.7V,  Z-Bolt 3500 mAh Lithium (Long Barrel) 

  • Battery: 2 pcs CR123A, Z-Bolt 1500 mAh (Duel Fuel - Long Barrel ONLY)

  • Surface - Anodized FDE

  • Warranty: 2 Years from Date of Purchase

  • Environmental Rating - IP65

  • Scout mount body

  • Includes Green & Red Predator Hunt Filters

  • Includes Twist On Beam Diffuser “Hot Spot & Spill”

  • Clicker tailcap switch

  • LEP Module: Fully Potted to Withstand Shock & Recoil

  • Length 168 mm, Width 33 mm

  • Weight: 5.4 ounces / 153 grams 

  • Body Material:  T6061 Aluminum Alloy

LED

  • Extreme Beam Throw: 200 Meter PID  

  • Run Time: 60 Minutes, 1 pc 18350 Lithium Rechargeable

  • LED & PCB: Fully Potted to Withstand Shock & Recoil

  • Battery: 1 pc 18350 - 3.7V,  Z-BOLT® 1400 mAh Lithium (Short Barrel)

  • Weight: 91 grams / 3.2 oz (without battery installed)

  • Length: 4 1/8 in. (104mm) (No Tailcap)

  • Body Material:  T6061 Aluminum Alloy

  • Surface - Mil-Spec Hard Coat Anodized: Z-BOLT® FDE

  • 65,000 Candela & 650 Lumens

  • Mid-Range Hot Spot & 60° Flood/Spill 

  • Superior Mid-Range Illumination & PID @ 50-100 Meters

  • Includes 1 pc Light Body Package & Choice of THYRM Pocket Clip

  • Switch Light Head Between Weapon Mounted & Hand Carry/Duty Carry/EDC

  • Scout mount body

  • Handheld body with clicker switch

  • Extra Momentary tailcap switch for weapon light body

What other aesthetic options or finishes are available?

Black versions, different mounting options, different tail caps

What others are saying?:

Not much found

Link to other reviews:

LEP - OreGear YouTube   

LEP - TFB review  

LED - Big Dick Ballistics

Price point:

MSRP = $228.00 and $298.00 as tested

Retail = LED’s start at $168.00

LEP’s start at $288.00

I need it now! Availability:

Z-Bolt Electro-Optics

Our Rating:

Pros:

  • Super long throw for LEP

  • LEP beam diffuser 

  • Good throw for LED

  • Handheld options

  • Standard Scout style mounting

  • Uses standard size 18650 & 18350 batteries

  • Different tailcap and switches available

  • LED light is priced well for what you get

Cons:

  • FDE colors don’t match each other

Score: 8.50 Great - for both lights

Favorite Link:  Zaffiri Precision P320 Slide

Viridian RFX45

  The enclosed emitter, red dot sight market, is getting packed with options. One of those options is the Viridian RFX45. Because it is from Viridian, it uses a green dot, not red, as green is what Viridian is known for. The RFX45 is mainly designed for pistols, but can be used on rifles. I’m mainly going to focus on it as a pistol optic.

  As mentioned, the RFX45 is a closed emitter dot style sight. Some people have nicknamed them “mailbox” sights, since they look like a mailbox sitting on top of your pistol. This is due to the square, boxy shape of the sight. The closed emitter sight has some distinct advantages over the open emitter style. For instance, the RFX45’s emitter won’t get dust or moisture on it. So the image of the dot stays clear. Yes, dust and moisture can get on the outside lenses, but this doesn’t affect the emitter itself and is easily cleaned off. I find enclosed style dot sights are easier for me to find the dot. This is due to it being easier to look down a tube, since my eyes find the center of a tube naturally. I know the RFX45 is technically a rectangle, but it still works better for me. To me there are only two disadvantages, and they really are small ones. Enclosed style sights, like the RFX45, can weigh more than open emitter style. The RFX45 only weighs around ¾ oz more than most open reflex sights. The RFX45 is still light enough that, most likely, you won’t have to change recoil springs, I didn’t. The next disadvantage could be their size. You might be more likely to hit it on something. Or, it might be harder to conceal under a shirt. Other than that, mailbox style sights, like the RFX45, are a great sight option.

  Most of the closed emitter sights you encounter will have the ACRO footprint, the Viridian RFX45 is no different. The ACRO style footprint is a little unique, in that it is kind of like a mini picatinny rail. This means that you will need an adapter if your slide is not specifically cut for an ACRO.  Do not fear, Viridian has different options as to what adapter plate the RFX45 comes with. Either a MOS, RMR, DOCTOR, or a low or high mount. The high mount is to mount it on an AR style rifle. The RFX45 I was sent had the MOS adaptor as the RMR ones were not out yet. I used a Primary Machine plate and it worked just fine. I do like how Viridian uses an “Industry Standard'' mounting platform for the RFX45.

Bottom dot is from the fiber optic front sight.

  The Viridian RFX45 is packed with useful features. First, the RFX45 has Instant-On. So whenever the sight senses motion, it turns the green dot on. If it sits for 2 minutes, the dot goes off until it senses movement again. This feature worked flawlessly in the RFX45. I had zero problems with it. Next up is the 50,000 hr battery life. This long battery life is also attributed to the Instant-On capability and its CR2032 battery. The green dot size is listed as 5 MOA which is slightly larger than some others. Since this is a green dot, the 5 MOA dot appeared to be slightly smaller to me. But either way, the 5 MOA dot size worked fine for everything I did with it. The RFX45 has 10 brightness settings, 2 of which are night vision compatible. At the highest setting, the RFX45 can be seen in direct bright sunlight. During my shooting experiences, some in bright sunlight, I could see the green dot just fine. 

  Window size can play an important role when choosing an enclosed red dot/green dot sight. The Viridian RFX45 has a 24mm wide x 15.5mm tall window size. This window size is wider than most of its competition. Most are 15mmx15mm. As mentioned previously, this window size makes the sight super easy for me to pick up. This includes under recoil, the draw stroke, and transitioning between target to target. The clear green dot probably helps a little with that too. All I can say is that I pick up the RFX45’s dot faster than my open reflex sights.

  Being the RFX45 is one of those mailbox style sights, I better explain some about its style. Yes, it’s square. But more on point is that the battery is housed at the top of the optic. So no removing the sight to change the battery. On the left side is a rubber pad with the up/down brightness buttons. The glass has an ever so slight tint to it. I never even noticed the tint, even on darker days. It’s super clear. Speaking of clear, the dot is extremely clear also. I have an astigmatism, and the dot doesn’t star out as much as some of my other green dots. For those of you with normal eyes, you will get a super clear round dot. I mounted the RFX45 to a Grey Ghost Precision slide that was cut for an RMR. Even with an adapter plate, the RFX45 sits level with the top of my slide. This allows me to still use the tall iron sights that are on the pistol. 

  So, if you are in the market for a “mailbox” style sight, do take a look into the Viridian RFX45. It may cost a little bit more than some others, but you are getting a quality enclosed green dot sight. I used it quite a bit and it never failed me, something I can’t say about the ammo I was using. You get a lot of high end features in the RFX45. You can check it out at Viridianweapontech.com

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Enclosed Green Dot reflex sight

Target Market:

Pistol shooters of all types, Law enforcement, Concealed carry, Competition

FNBs (Features & Benefits of this product):

  • ACRO footprint

  • Dimensions 1.9" x 1.1" x 1.13"

  • Lens Dimension: 24mm x 15.5mm

  • Unlimited eye relief

  • Fully Multi Coated Glass

  • 90 MOA of adjustment

  • 5 MOA Green dot

  • 1 x CR2032

  • Battery Life: Up to 50k+ hours

  • Settings: 10 | 8 Visible and 2 Night Vision

  • Operation: INSTANT-ON + User Controlled brightness

  • Weight: 1.73oz / 48.19 grams

  • 6061 Aluminum w/ Hard Coat Anodization

  • IPX6 rated

  • Operating Temperature: -4F to 130F

  • Limited Lifetime Warranty

  • MOS, RMR, Doctor, & Picatinny mount versions

What other aesthetic options or finishes are available?

None

What others are saying?:

Couldn’t find anything

Link to other reviews:

GunDeals YouTube    

Price point:

MSRP = $459.00

Retail = $399.99 at GunMagWarehouse   

I need it now! Availability:

Viridian or GunMagWarehouse

Our Rating:

Pros:

  • Crisp clean dot

  • Enclosed so dirt and water do not get on emitter

  • Decent size window

  • Actual click adjustments

  • Battery life

  • Instant on motion activation

Cons:

  • Price

  • Needs adapter plate for most applications

Score: 8.00 Great

Favorite Link:  Viridian RFX 35 review

Virtual Shot - Pistol

  Virtual Shot has come out with their multi platform dry fire mount. I previously reviewed the original mount and app here: Virtual Shot Review. So I won’t be covering much on the APP or rifle parts of it. The new Virtual Shot mount has pistol and scope style mounting platforms that give it even more usability. I’m mainly going to focus on the pistol mount.

  The Virtual Shot shot mount has been upgraded from the original. The mount now has a stouter mounting stem. This stem is the base part in which you can mount the picatinny, pistol, or scope adapters to. When I say stouter, the mounts are now more robust than the original. The stem is also where you mount your phone. The actual phone mounting is way better than the original. It also accepts larger phone sizes. This new phone clamp also holds the phone better than the original Virtual Shot mount. The mount also uses thumb screws to adjust everything. All of this makes a better mounting system for your dry fire practice.

   To change the mounts, Virtual Shot includes a screwdriver and some other parts. Essentially you unscrew that stem system and install whichever mount you want to use. The picatinny adapter is used for both the pistol and AR style mount. It just gets flipped over and mounted differently. For the pistol, there is also an angle mount that extends the phone mount past your muzzle, and then hooks to your pistol's front rail. If using it on a rifle scope, the new ring style scope mount is used to install on the ocular eyepiece of your scope. This sets the phone in front of your scope, so you can use the Virtual Shot system just like you would your normal scope, well kind of. It is still slightly different from shooting in real life, but nothing major.

  Now it’s time to get into the pistol mount and what it does. Since the Virtual Shot is a system, of course you have to mount it to a pistol. The app asks all kinds of questions to make sure everything is unloaded and safe. I used the pistol mount on a Lone Wolf framed pistol, so a Glockish style handgun. Part of the reason I did this is because I used a TTrigger dry fire magazine. The TTrigger mag is currently only made for Glock style pistols. The TTrigger mag allows for the trigger to reset continually on the pistol it is installed on. The TTrigger mag also makes a clicking sound every time the trigger is pressed, think dog clicker trainer. Your phone picks up the clicking sound, so the Virtual Shot app knows you're firing a shot. If you are using other pistol platforms, a DryFire magazine does the same thing. Now, the Virtual Shot app did have a few problems always picking up the sound. Did it cause problems? Not really, because most of the time you can just re-pull the trigger. It did make the “Pistol Competition” harder for me since it had moving targets. Virtual Shot recommends the DryFire mag, so it may work better with the app then the TTrigger mag. If you happen to have an airsoft or pellet pistol that uses some sort of propellant, the mount will also work with those, unloaded of course. Virtual Shot includes a blast diverter to divert that muzzle blast gas away from your phone. Overall I was happy with how the TTrigger mag worked with the Virtual Shot system. After all, it’s way better than just old school dry fire.

  There are some new items in the app. Most of these apply to the new pistol stuff. There are pistol training videos and competitions. All the other aspects of the app will now allow you to use the pistol. As one can expect, the training videos are just exactly what they say, training videos. The Competition section is pretty cool. Every month Virtual Shot has some sort of competition in this section. Sometimes it’s rifle, sometimes it’s pistol, you get the idea. But what is cool about this section, is that you play for actual prizes! You compete with other people using the app. I did get 2nd or 3rd once with the pistol. Since I received the Virtual Shot stuff for free, I didn’t feel right getting a prize, I think I may have talked them out of it. I will mention that it took me forever to get the score I got. But don’t fret, it takes your highest score no matter how many times you try. It really is pretty cool testing your skills against other people from around the world.

  When using the pistol in the Virtual Shot app, there are different sight options. These different sighting options haven’t changed, but some of them are more rifle’ish. There is still a red dot, circle dot, crosshair, AR style front sight, etc. All of these can be sized up or down. I tended to use the circle dot or just plain red dot. You can also move them around the screen. This movement allows you to line the sighting system up with your sights. If you are using an actual red dot, just line the apps dot up inside your dot, as you are looking through it. I used an iron sighted pistol. So I lined the red dot, in the app, up with my sights, then turned it to super small. This allowed me to use the iron sights. I will say that I quickly went to the circle dot and used it instead of my pistol's iron sights. It would be nice if they had a pistol front sight, similar to the AR one, to use in the app. But, the way I did it worked fine. 

  The new mounting systems from Virtual Shot is far better than the original one. Yes, the app still has all the great features it previously did in my original review. The new “play with friends” and “competitions” are the only real new app features, and they are pretty neat. Having the ability to play the “mini games” and “challenges” with a pistol brings a whole new aspect to the Virtual Shot system. If you are looking for something different to help you with your dry fire practice, look into the Virtual Shot system.

Firearms Insider Reviews - 8 Key Points

Claim to Fame:

Dry fire training aid

Target Market:

Those who want a unique dry fire experience 

FNBs (Features & Benefits of this product):

  • New mounting system for phone

  • Pistol mount option

  • Scope mount option

  • Effective bullet drop and wind drift

  • Customizable ranges

  • 100+ shooting levels

  • Mini games

  • Practice ranges

  • Shooting analytics

  • Video Shooting courses

What other aesthetic options or finishes are available?

None

What others are saying?:

Nothing really found on just the pistol portions of the app

Link to other reviews:

TFB review of original Virtual Shot

Price point:

MSRP = $149.00

TTrigger mag as used - $104.99

I need it now! Availability:

Virtual Shot

Our Rating:

Pros:

  • Great dry fire training aid

  • New mount is nice

  • Scope mount ring

  • Better picatinny mount

  • Pistol mount

  • Can be used on airsoft pistols

Cons:

  • Doesn’t always pick up clicks from dry fire magazines

  • Apps auto reset is a little slow

Score: 7.50 Good

Favorite Link:  Original Virtual Shot Review